CONNECTIONS
EQ
EQUALIZER
INTEGRATED CIRCUIT
AC 220-230V~50Hz
POWER CONSUMPTION: 10W
R
E
M
O
T E
S
YS T E M
TU
G
N
D
E
Q
TAP
E
N
E
R
C
D
RIGHT
LEFT
INTEGRATED CIRCUIT
AC 220V - 230V ~ 50Hz
TAP
LAY
E
E
Q
AV1
AV2
P
H
O
N
O
C
D
TU
N
E
R
P
R
E
C
P
LAY
R
E
C
L
R
_
_
S
P
E
A
K
E
R
S
6
~
8
Ω
A
U
D
I O
Connection Precautions
ꢀ
When connecting, either disconnect the power plug from the power outlet or turn off the unit’s power using the
POWER switch.
ꢀ
Before connecting, read through the Operation Instructions of the other audio components which will be connected to
this unit.
ꢀ
ꢀ
Check the left and right channels and connect properly (L to L and R to R).
Insert the plugs securely. Improper connection can lead to the generation of noise.
PANEL INFORMATION
1
2
3
11
10
9
8
7
6
5
4
1. ON/STANDBY SWITCH
Depress button to switch “ON” the unit. Press release to switch “OFF” unit into “STANDBY MODE”. If the unit is left
unattended for long periods, remove the A/C plug from the power socket.
2. SPECTRUM DISPLAY
This displays the sound level different frequency bands (Because the level indicator is connected to the input side, the
indication does not change when the VOLUME control is turned.
3. EQUALIZER SETTING
These settings allow the levels approximate to the frequencies indicated above the controls to be continuously controlled
from +12 dB to –12 dB for the left and right channels separately.
Press key (◄) to shift the lower frequency band and key (►) to shift the higher frequency band that you want to adjust.
When arrived to the pre-decided band, relative indicator will flash.
Press level UP (▲) control key or level down control key (▼) to the level that you wish to create, then press MEMORY
key and select (A-E) to program. And 5 different sets of personally created sound fields can be stored.
4. EQ MODE SWITCH (FINE/ALT)
Press the EQ mode switch (4), the word ALT is displayed and the alternating band level can be adjusted. And press it once
again, the word FINE is displayed & each succeeding sound level can be adjusted.
5. EQUALIZER FLAT BUTTON
This button is used to turn the equalizer flat.
This equalizer also has five pre-memorized 5 different level curves of sound mode including.
6/7/8/9. CLASSIC/ DISCO / JAZZ / ROCK SWITCH
If you are listening to the above 4 kinds of music, press the relative modes of switch. The best sound effect will be heard.
10. DISPLAY/MEMORY MODE SWITCH
This EQ spectrum has 5 display modes. When pressing DISPLAY/MEMORY switch once, one of the 5 display modes will
be appeared. And press once again, another one display mode appeared and similarly.
When you have set the sound level curve of the equalizer personally, pressing the DISPLAY/MEMORY switch, “MEMO”
will be lit up in the display. And press A-E to memorize it in A-E preset knobs.
11. USER PRESET SWITCH
You can press A-E to take your preset sound level curves.
OPERATING PROCEDURES
EQ
EQUALIZER
INTEGRATED CIRCUIT
AC 220-230V~50Hz
POWER CONSUMPTION: 10W
R
E
M
O
T E
S
YS T E M
TU
G
N
D
E
Q
TAP
E
N
E
R
C
D
RIGHT
LEFT
INTEGRATED CIRCUIT
AC 220V - 230V ~ 50Hz
TAP
LAY
E
E
Q
AV1
AV2
P
H
O
N
O
C
D
TU
N
E
R
P
R
E
C
P
LAY
R
E
C
L
R
_
_
S
P
E
A
K
E
R
S
6
~
8
Ω
A
U
D
I O
* Switch on the Amplifier or the sound source.
* Select “EQ” from function selection column at the amplifier or the processor, the relative light will be seen when selected.
* Switch on the Equalizer by pressing the Power switch (1).
* Bars of spectrum display in equalizer will be jumping.
* Press DISPLAY/MEMORY switch, 5 different kinds of display will be shown.
* When selecting the pre-memorized sound level curves, pressing the SOUND MODE SWITCH (6-9), the relative word
and sound curve will be seen. A few seconds later, the display will change to spectrum mode automatically.
* If you want to adjust the your favourite sound level curve, press EQUALIZER SETTING(◄)/ (►), the display will
change from spectrum mode to EQ mode. Choose the frequency firstly, you can adjust the frequency band alternatively
(by pressing ALT) or each succeeding frequency band (by pressing FINE). Then pressing EQUALIZER SETTING (▲)/
(▼) to adjust your favourite sound level. After adjustment, press DISPLAY/MEMORY switch, “MEMO” will be seen on
the display and press A_E preset. Your 5 favourite sound level curves can be stored in the User Preset Switch.
* Press User Preset Switch to take your pre-memorized sound level curve.
EQUALIZER CHARACTERISTIC
Variable range…………………………………±12 dB/ (L & R independently adjustable)
Center frequencies…………………………….63Hz, 160Hz, 400Hz, 1KHz, 2.5KHz, 6.3 KHz, 16 kHz
Total harmonic distortion…………………….Less than 0.1% (20 Hz to 20 kHz)
Maximum output voltage…………………….6V (THD 0.05%)
S/N ratio……………………………………….60 dB (1HF-A network, 1 V)
Input impedance……………………………….47 kohms
Output impedance……………………………..15 kohms
General
Power consumption…………………………….10W
Power requirements
Power voltage………………………………….220V ~ 50Hz
For U.K…………………………………………240V ~ 50Hz
For U.S.A & Canada……………………………110V ~ 60Hz
Power consumption……………………………. 10 Watts maximum
Dimensions……………………………………….. 420 mm x 93 mm x 215 mm (W x H x L)
Weight……………………………………………..2.7 Kg
Note: We follow a policy of continuous advancements in development, for this reason specifications may be changed
without notice
|