Sanyo Installation
Configuration and Connections
SYSTEM 4xi
PROJECTOR COMMUNICATIONS KIT
ATTENTION!
PLEASE READ THIS DOCUMENT FOR IMPORTANT
INSTALLATION INSTRUCTIONS
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:
Kit Type: SANYO
Included Communications Adapter(s):
Quantity
Part Number
26-467-01
26-489-01
Description
ADP, UNV, “A”
ADP, UNV, “J”
1
1
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING
COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS
MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS
INDICATED BY THE “✔” IN THE “CONFIG AS” COLUMN. IF YOUR PROJECTOR MODEL
DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER
WITH THE CORRECT SETTINGS.
PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND
SIGNAL CONNECTION INSTRUCTIONS.
THIS SWITCHER HAS BEEN CONFIGURED FOR: SANYO PLC
CONFIG
AS
MODEL
SW1
SW2 SW3 SW4 SW5 SW6 PROJ
COMM
1
2
3
4
CABLE ADAPTER
✔
✔
PLC
off on off on
off on off on
off on off on
0
0
0
0
0
0
1
1
1
E
E
E
0
0
0
J15
J15
J15
26-467-01
26-489-01
26-489-01
PLC 8810
PLC XP10
PLC XP30
off on off on
0
1
1
E
0
J15
26-489-01
Page1
Extron • System 4xi Switcher Series • User’s Manual • P/N 68-402-02 Rev. E
Sanyo Installation
Configuration and Connections
5. The Sanyo PLC Comm Adapter (26-467-01) has a 9-pin male connector that
accommodates the Comm Extension cable. The other end of the Comm Adapter
plugs into the projector’s RS-232C port.
6. Plug the 15-pin HD connector of the Projector Communications Extension cable
into the PJ Comm port on the System 4xi.
______ Secure all of the connector screws.
7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV
cable onto the System 4xi output and those on the other end onto the matching
BNCs on the Sanyo PLC connector panel.
System 4xi Series – Sanyo PLC Projector Connections
Use the illustration below as a guide when connecting the System 4xi to a Sanyo
PLC Projector. Refer to Sanyo documentation to continue the installation.
See Special Note below
R
G
B
H
V
USB 1 CONTROL PORT 1
VIDEO/Y C/Cb(B-Y) Cr(R-Y)
VIDEO/Y C/Cb(B-Y) Cr(R-Y)
VIDEO/Y C/Cb(B-Y) Cr(R-Y)
S-VIDEO
S-VIDEO
S-VIDEO
AUDIO 1
AUDIO 1
R
L
R
L
ANALOG RGB
ANALOG RGB
AUDIO 1
USB 2 CONTROL PORT 2
AUDIO 2
R
L
R
L
AC JACK SERIAL PORT
AUDIO 1
AUDIO OUT
R
L
R
L
9-Pin Male
ComAdapter
26-467-01 "A"
or 26-489-01 "J"
A
9-Pin Male
9-Pin Female
RGBHV 5 BNC
15-Pin
Male
INPUT 1
H/HV
INPUT 2
INPUT 3
INPUT 4
H/HV
OUTPUT
H/HV
PJ COMM
V
H/HV
V
H/HV
V
V
V
AUDIO
AUDIO
B
AUDIO
AUDIO
B
AUDIO
RS 232
R/C
G/Y
B
R/C
G/Y
R/C
G/Y
B
R/C
G/Y
R/C
G/Y
B
____________ In a rack mount, do NOT allow the weight of the cables to be supported by the
System 4xi. See page 2-5 for cabling guidelines.
Special Note: _____ Certain PLC projectors may not come equipped with a 9-pin serial port
connector. In those situations, the Com adapter must be connected to Control
Port 2 using the projector’s special DIN to 9-pin serial adapter, as illustrated
below.
t
To switcher's Projector Control por
ort 2
To projector's Control P
Sanyo DIN to 9-pin adapter
Extron Com Adapter
26-467-01 "A"
or 26-489-01 "J"
Page3
Extron • System 4xi Switcher Series • User’s Manual • P/N 68-402-02 Rev. E
|