Assembly Instructions for Model: WFV44
Thank you for choosing Sanus Systems Woodbrook Furniture. The Woodbrook Furniture is
constructed of real hardwood and resonance dampening MDF.
Safety Warning: If you do not understand these directions, or have any doubts about the
safety of the installation, please call a qualified contractor or contact Sanus at 800.359.5520 or
customer service representatives can quickly assist you with installation questions and missing
or damaged parts. Replacement parts for products purchased through authorized dealers will be
shipped directly to you. Never use defective parts. Improper installation may cause damage or
serious injury. Do not use this product for any purpose that is not explicitly specified by Sanus
Systems. Sanus Systems can not be liable for damage or injury caused by incorrect assembly, or
incorrect use. Please call Sanus Systems before returning products to the point of purchase.
Required Tools: Phillips screw driver
Supplied Parts and Hardware: Some parts may be pre-assembled together*
Hardware: Shown as actual size
(16) Cam Pin - a
(6) Dowel Pin - c
(16) Dowel - d
(16) Shelf Pin - e
(16) Cam - b
(8) Wood Screw - f
(6) Spacer - g
(4) Phillips Bolt - h
(2) Door Handle - i*
(8) Hinge Screw - j
(8) Hinge Plate Screw - k
Parts: Not Shown as actual size
(4) Hinge - l*
(4) Hinge Plate - m*
(4) Back Stretcher - p
(4) Front Stretcher - o
(1) Top - n
Sanus Systems 2221 Hwy 36 West, St. Paul, MN 55113 12.28.05
Step 2: Prepare Stretchers
Add a Cam (b) to each Front Stretcher (o) and Back Stretcher (p). Make sure the arrow in each Cam faces the hole on the side of the
Stretchers. See Diagram 2 for assistance.
Diagram 2
Detailed View
o
a
arrow
p
Step 3: Add Stretchers
Add the Front and Back Stretchers (o,p) to the Side Panel (u), by aligning the Cam Pin (a) with the hole which the Cams (b) point to and
the Dowel goes into the adjacent hole. Make sure the stretchers are oriented so the Cams face inward. Tighten each Cam closest to the
Side Panel in a clockwise motion until the stretchers are secured. Note: Front stretchers attach to the same side as the hinge
holes are on.
Detailed View
Diagram 3
u
d
hinge
holes
b
a
p
Step 4: Add Center Panel
Press fit the Center Panel (w) against the Stretchers (o,p) so the Cam Pin (a) goes into the hole which the Cams (b) point to. The Dowel
fits into the adjacent hole. Tighten each Cam in a clockwise motion until the Stretchers are secured to the Center Panel. See Diagram 4
for assistance. Note: Make sure the hinge holes on the Center Panel are on the same side as the Front Stretchers.
Detailed View
Diagram 4
o
a
hinge
holes
w
d
Step 5: Add Stretchers
Add the Front and Back Stretchers (o,p) to the Center Panel (w), by aligning the Cam Pin (a) with the hole which the Cams (b) point to.
The Dowel (d) goes into the adjacent hole. Make sure the stretchers are oriented so the Cams face inward. Tighten each Cam closest to
the Center Panel in a clockwise motion until the stretchers are secured. Note: Front stretchers attach to the same side as the
hinge holes are on.
Diagram 5
Detailed View
x
a
b
hinge
holes
d
p
Step 6: Add Side Panel
Press fit the Side Panel (v) against the Stretchers (o,p) so the Cam Pin (a) goes into the hole which the Cams (b) point to. The Dowel (d)
going into the adjacent hole. Tighten each Cam in a clockwise motion until the Stretchers are secured to the Side Panel. See Diagram 6
for assistance. Note: Make sure the hinge holes on the Side Panel are on the same side as the Front Stretchers.
Detailed View
Diagram 6
a
hinge
holes
o
v
Step 7: Add Shelf Pins and Bottom Shelf
Thread the Shelf Pins (e) into the bottom hole in the line of holes in each Panel (u,v,w). Tighten Shelf Pins with a Phillips screw driver.
Add the Bottom Shelf (q) by inserting it into the assembly and press fit it onto the Shelf Pins. Make sure the Bottom Shelf is flush
against the Front Stretcher (o). If there is a gap in front, shelf may be backward. See Diagram 7 for assistance. Note: Diagram 7 is a
Back View.
Detailed View
Diagram 7
w
u
e
q
v
Step 8: Add Top
Gently tap a Dowel Pin (c) into the holes on the top of each Panel (u,v,w). Slide a Spacer (g) over each Dowel Pin. Press fit the Top (n)
so it fits onto the Dowel Pins. See Diagram 8 for assistance.
Detailed View
Diagram 8
n
c
g
v
Step 9: Prepare Doors
Insert each Phillips Bolt (h) through the Door (s) and into the Door Handle (i). Tighten with a Phillips screw driver. See Diagram 9a for
assistance. The Door Panels can be interchanged by removing and re-installing the plastic border from the perimeter of the Door’s back
side.
Insert a Hinge Screw (j) through the Hinge (l) and thread it into the Door (s). Tighten each with a Phillips screw driver. Repeat process
until each Hinge Assembly is secure. See Diagram 9b for assistance.
Diagram 9a
Diagram 9b
Detailed View
Detailed View
h
i
s
s
l
j
Step 10: Door Install
Position the Door (s) so the holes in the Hinge Plate (m) line up with the front pair of holes in the Side Panel (u,v). Insert a Hinge Plate
Screw (k) through the Hinge Plate and thread it into each hole in the Side Panel. Tighten with a Phillips screw driver. Repeat process so
each Hinge Assembly is secured. See Diagram 10 for assistance.
Detailed View
Diagram 10
s
m
k
u
Step 10: Add Mid Shelves
Thread a Shelf Pin (e) into the desired location in the Panels (u,v,w). For each shelf, four Shelf Pins will be required. Insert each Mid
Shelf (r) into the assembly and press fit onto the Shelf Pins. Make sure the wood strip on each shelf is facing toward the front. See Dia-
gram 10 for assistance. Note: Diagram 10 is a Back View.
Detailed View
Diagram 10
u
v
w
e
r
Step 11: Add Back Panel
Position each Back Panel (x) up against the assembly and thread a Wood Screw (f) through it and into the Back Stretcher (p). Repeat
process until each Back Panel is secured with four Wood Screws. Tighten each with a Phillips screw driver. See Diagram 11 for assis-
tance.
Detailed View
Diagram 11
p
f
x
Step 12: Hinge Adjustment for Woodbrook Door
Each hinge Assembly is adjustable in multiple directions. See Diagram 12 for assistance.
Diagram 12
Side Adjustment
Depth Adjustment
Height Adjustment
Sanus Systems 2221 Hwy 36 West, St. Paul, MN 55113 12.28.05
|