Sanitaire Vacuum Cleaner S634 User Guide

Heavy Duty  
Upright Vacuum Cleaner  
Household Type  
Ownerʼs Guide  
Model S634  
IMPORTANT  
Do not return this product to  
the store. Call 1-800-800-8975*  
Monday - Friday, 8 am to 7:30  
pm CST and 10 am to 6:30 pm  
Saturday or visit our web site,  
of the following:  
• assembly problems  
• replacement of broken or missing  
items  
• to order replacement parts and  
accessories  
• to locate the nearest Sanitaire  
Warranty Station  
*En Mexico llame al (55) 5343-4384  
PLEASE RETAIN  
We suggest you record the model, type and serial  
numbers below. They are located on the silver rating  
plate on your cleaner. For prompt and complete  
service information, always refer to these numbers  
when inquiring about service.  
Model & Type  
Serial No.  
It is also important to keep your receipt as proof of  
date of purchase.  
Part No. 75325
(12/04)  
©2004 Electrolux Home Care Products Ltd.  
Printed in U.S.A.  
 
Step 4  
Outer Bag  
HOW TO ASSEMBLE  
CAUTION: Completely assemble vacuum cleaner before  
using.  
Hold outer bag with zipper away from handle.
Important:  
To provide a good gasket seal, the bag coupling must  
seat firmly against the motor base and not overlap the  
furniture guard.
Start the bag screws D by hand, then tighten  
with a screwdriver.  
Handle styles may vary. One handle has four snap pins on  
the back side of the handle, the other handle has two snap  
pins on each side. The cord hooks may be different.  
Assembly Packet  
Step 5  
Bag Support  
Loop the spring F onto the bag support G, located to the back of  
the upper cord hook.  
A - CONNECTOR  
G
Step 1  
Handle Connector  
Upper  
Upper Cord  
Guide  
Hook  
Push connector A into the upper  
handle and align holes. One  
connector, shown, is flat on one  
side and the 4 pins snap into one  
side. The
 
connector in Detail A  
has 2 snap pins on each side and  
alignment tabs that slide into the  
handle.  
F
B
A
Step 2  
Fastener  
Push fastener B into a hole and  
apply thumb pressure so fastener  
snaps into position. Secure second  
fastener. Repeat steps 1 and 2  
to complete the assembly of the  
handle. See Detail B.  
B
E
C–  
Lower Cord  
Hook  
D
E
Step 6  
Cord Storage  
C –  
Tab  
Secure the cord in the guide below the upper cord hook as  
shown or secure the cord into the side of the upper cord  
hook.  
Secure cord into lower cord hook. Pull up on cord to tighten  
but leave slack near the base so the cord does not strain when  
the handle is lowered for use. Wrap the cord around the cord  
hooks. Fasten the plug to the cord to prevent unwinding.  
Detail A  
Detail B  
Step 3  
Handle Socket  
Push handle into handle socket E so handle grip curves  
away from the cleaner. Align the holes, insert the 2-part bolt  
C and tighten.  
3
 
How To Use  
The upright vacuum cleaner is designed to be used on  
multiple types of carpeting. Do not attempt to use the  
upright vacuum cleaner on bare floors, as damage to the  
floor covering may result. Above the floor cleaning tools are  
available (optional).  
Cord Storage  
1. Store  
The cleaner has two convenient cord storage hooks attached  
to the handle. However, some models feature a quick release  
cord hook on the upper handle.
A
d
ownward twist of the cord  
hook frees the cord for quick removal. With either style, wind  
the cord around the hooks for storage. Fasten the plug to the  
cord to prevent unwinding.  
2. Use  
Cleaner Height Setting  
3. Clean  
Underneath  
WARNING: Avoidinjury.Keeplooseclothing,hair,ngers,  
and all other parts of body away from any  
moving part (such as the revolving brush).  
Turn off the switch and unplug the cleaner  
before changing the cleaner height setting.  
Handle Lock  
The front of the cleaner has an adjustment that raises or  
lowers the cleaner base to match the type of carpet. With  
the cleaner cord unplugged, set the adjustment to lowest  
setting for maximum cleaning. If the cleaner is difficult to  
push, move adjustment to next highest setting until cleaner  
is comfortable to push. The brush roll must reach the carpet  
for effective cleaning.  
Make each adjustment with cleaner switch off and  
cord disconnected from outlet. For ease in moving the  
adjustment knob, place handle in operating position and tilt  
cleaner back to remove weight from front wheels.  
Handle Adjustment  
With the tip of the foot, press down to release the handle lock  
located at the left rear side of the cleaner. Move the handle  
and adjust it to the desired position for (1) storing upright, (2)  
operating the cleaner at a comfortable height for the user,  
and (3) cleaning underneath low furniture.  
ON/OFF  
HOW TO MAINTAIN  
The instructions given in this booklet serve as a guide to  
routine maintenance.
T
o
a
void unnecessary service calls,  
check the bag, belt and brush roll often.  
Disposable Dust Bags  
Paper bags play a very important role in the efficiency of a  
vacuum cleaner. The purpose of a paper bag is to trap dirt.  
But at the same time the bag must be porous enough to allow  
air to pass through. If the paper bag becomes clogged, no  
air can pass through the cleaner and no cleaning can take  
place, regardless of how powerful the unit is. Change the dust  
bag frequently. Some fine particles can restrict airflow very  
quickly and will decrease performance even before the bag  
appears to be full. For that reason, when vacuuming carpet  
fresheners or cleaners, powder, plaster dust, or similar fine  
substances, the bag may need to be changed more often.  
Power Switch  
The power switch is mounted on the motor hood. A push  
with the foot turns the motor ON; push again to turn the  
motor OF
F
.  
4
 
How To Change Disposable Dust Bag–Style F  
& G, PN 54924A  
Brush Roll Belt  
The brush roll belt on the upright vacuum cleaner drives the  
brush to agitate, sweep, and comb the carpet nap. The belt  
should be checked regularly to be sure it is in good condition.  
Replace the belt if it is stretching, cracking, or slipping. Cut  
away any hair or thread wound around the brush roll or the  
belt pulley because the buildup could cause the belt to rotate  
unevenly.  
CAUTION: Turn off the switch and unplug the electrical  
cord before changing dust bag. Never operate  
the vacuum cleaner without the dust bag.  
How To Replace A Worn Belt, Style RD,  
PN 52100A  
1. Pull  
CAUTION: Turn off the switch and unplug the electrical  
cord before replacing belt. Belt pulleys can  
become hot during normal use. To prevent  
injury, avoid touching the belt pulley when  
servicing the drive belt.  
zipper  
2. Roll down  
down  
coil spring.  
3. Pull bag  
throat off  
sleeve.  
IMPORTANT: Improper installation of the brush roll  
or brush roll belt could cause carpet or  
cleaner damage.  
4. Unfold  
new bag.  
THR  
5. Place bag  
throat on  
sleeve.  
6. Roll up coil spring.  
1. Release cam locks.  
7. Place paper bag into outer bag.  
Motor  
NOTE: Be certain there are no folds  
at the top or bottom of the  
paper bag.  
8. Lift zipper  
GENUINE  
Look for the  
symbol.  
2. Pull up on belt to rotate it off the motor pulley. Lift  
up on brush roll and remove worn belt.  
Ask for GENUINE EUREKA dust bags – Style F & G.  
Cleaner Care  
e
CAUTION: Turn off the switch and unplug the electrical  
cord before cleaning unit.  
To
k
eep the vacuum cleaner looking new, it can be wiped with  
a damp cloth and a mild soap solution, then thoroughly dried.  
Never use any type of chemical as chemicals can damage  
the cleaner. When not in use, the cleaner should be stored  
in a clean, dry place.  
Brush Roll Pulley  
Check for brush wear, see Brush Roll instructions.  
3. Place new belt around brush roll.  
4. Align brush roll pulley with belt guide.  
5
 
How To Replace A Worn Belt (continued)  
Brush Roll  
The rotating brush roll sweeps and combs the carpet nap.  
Keep the brush roll free from hair and threads so it will con-  
tinue brushing. When the bristles of the brush roll no longer  
touch a straight edge held against the bottom plate, the  
brush roll is ineffective because the bristles no longer touch  
the carpet nap.
T
o
m
aintain the most effective cleaning, the  
brush roll should be replaced.  
5
Headlight Bulb (Standard on most models),  
PN 40009A  
5. Place rubber end cap covers over both end caps (flat  
side against end cap). Align holes and secure. Then,  
slant brush roll forward so end caps are in line with  
slots in cleaner base.  
CAUTION: Turn off the switch and unplug the electrical  
cord before replacing headlight bulb.  
6. Push brush roll into base.  
Headlight style varies by model. Locate the notches that  
release the tabs at either (1) top, (2) side, or (3) bottom of  
the lens, as illustrated. Place a screwdriver into one notch;  
twist or pry the screwdriver to release the lens. Repeat for  
the second notch on the opposite side.  
Rotate the bulb socket forward. Push bulb in and turn to  
remove. Secure new bulb into socket and rotate bulb socket  
backward.  
Replace the lens tabs into the top or the bottom of the hood  
opening. Rotate lens to position and press down at notch  
until the lens locks into position.  
7. Place lower side of belt into belt guide and pull to  
stretch the belt around the left side of the motor  
pulley. Rotate pulley to secure belt into groove.  
CAUTION: Use 25 watt replacement bulb, only.  
Ask for GENUINE EUREKA replacement bulb, 40009A.  
1
2
3
8
8
8. Place slots of bottom plate over tabs of cleaner  
base.  
9. Seat and secure cam locks  
Ask for GENUINE EUREKA replacement belts, Style RD  
No. 52100A.  
GENUINE  
Look for the  
symbol.  
6
 
THE SANITAIRE LIMITED WARRANTY  
W
hat This Warranty Covers  
Your Sanitaire cleaner is warranted to be free from all defects in material and workmanship in normal household use for a period of two years.  
The warranty is granted only to the original purchaser and members of his or her immediate household. The warranty is subject to the following  
provisions.  
W
hat This Warranty Does Not Cover  
Parts of the cleaner that require replacement under normal use, such as disposable dust bags, filters, drive belts, light bulbs, and brush roll  
bristles.  
Damages or malfunctions caused by negligence, abuse, or use not in accordance with the Ownerʼs Guide.  
Defects or damages caused by unauthorized service or the use of other than Genuine Eureka/Sanitaire parts.  
W
hat Electrolux Home Care Products North America Will Do  
Electrolux Home Care Products NorthAmerica will, at its option, repair or replace a defective cleaner or cleaner part that is covered by this warranty.  
As a matter of warranty policy, Electrolux Home Care Products North America will not refund the consumerʼs purchase price.  
E
xtended Warranty for Upright Cleaner  
The base of the Sanitaire Upright cleaner is warranted for five years from the original date of purchase.  
E
xtended Warranty for SYSTEM_PRO Uprights  
The suction motor for SYSTEM_PRO upright cleaners is warranted for five years from the original date of purchase.  
W
arranty Registration  
Please fill out and return the warranty registration card accompanying your cleaner.  
O
btaining Warranty Service  
To obtain warranty service you must return the defective cleaner or cleaner part along with proof of purchase to any Sanitaire Authorized Warranty  
Station. You will find the nearest location in the Yellow Pages, under “Vacuum Cleaners–Service and Repair.” Be certain that the Warranty Station  
is “Sanitaire Authorized.” For the location of the nearest Sanitaire Authorized Warranty Station or for service information, telephone toll free:  
USA: 1-800-800-8975  
Mexico: (55) 5343-4384  
Canada: 1-800-800-8975  
If you prefer, you can write to Electrolux Home Care Products North America, Service Division, P.O. Box 3900, Peoria, Illinois 61612, USA. In  
Canada write to Electrolux Home Care Products North America, 866 Langs Drive, Cambridge, Ontario N3H 2N7.  
If it is necessary to ship the cleaner outside your community to obtain warranty repair, you must pay the shipping charges to the SanitaireAuthorized  
Warranty Station. Return shipping charges will be paid by the Warranty Station. When returning parts for repair, please include the model, type,  
and serial numbers from the data plate on the cleaner.  
F
urther Limitations and Exclusions  
Any warranty that may be implied in connection with your purchase or use of the cleaner, including any warranty of Merchantability or any  
warranty for Fitness For A Particular Purpose is limited to the duration of this warranty. Some states do not allow limitations on how long an  
implied warranty lasts, so the above limitations may not apply to you.  
Your relief for the breach of this warranty is limited to the relief expressly provided above. In no event shall Electrolux be liable for any consequential  
or incidental damages you may incur in connection with your purchase or use of the cleaner. Some states do not allow the exclusion or limitation  
of incidental or consequential damages, so the above limitation or exclusion may not apply to you.  
This warranty gives you specific legal rights. You may also have other rights which vary by state.  
GENUINE  
EUREKA PRODUCT  
Q
uestions & Answers about Genuine Eureka/Sanitaire Products  
Q: Why should I use only Genuine Eureka/Sanitaire paper bags, belts, and parts in my Eureka/Sanitaire vacuum cleaner?  
A: Using Genuine Sanitaire Products, which are made to our exacting specifications and engineered with emphasis on quality,  
performance, and customer satisfaction, ensures the long life and cleaning efficiency of your vacuum cleaner. Overall, this  
saves you money and helps to keep your home clean.  
Q: How can I be sure I am using only Genuine Eureka/Sanitaire products in my vacuum cleaner?  
A: Typically, packaged products and paper bags can be identified by a Eureka or Sanitaire logo. For further identification  
assistance, you may call our toll-free number, 1-800-800-8975, for the location of a nearby Eureka/Sanitaire Authorized  
Warranty Station.  
Q: Are there any differences between “made to fit” or “imitation” and Genuine Eureka/Sanitaire paper bags, belts, and parts?  
A: Yes, there are some very important differences in materials, quality, and reliability. Many customers have mistakenly  
purchased “imitation” paper bags and parts while thinking they purchased genuine. Unfortunately, many of these customers  
discovered the differences after they experienced related difficulties.  
For Genuine Sanitaire Value, Accept No Imitations!  
ELECTROLUX HOME CARE PRODUCTS NORTH AMERICA  
Household Warranty  
Bloomington, Illinois 61701  
 

Q See Security Camera QSDS4936D User Guide
Quadra Fire Indoor Fireplace QV PIER User Guide
Rangemaster Cooktop RC90 User Guide
RIDGID Drill RB 214 User Guide
Roper Refrigerator RT14BKXS User Guide
Royal Sovereign Laminator ES 400C User Guide
Russell Hobbs Microwave Oven RHM2009S User Guide
Samsung Computer Drive SH S203D User Guide
Samsung DVD Player AK68 00411A User Guide
Samsung Printer ML 167X User Guide