TX-T2781
TX-T2782
TX-T2082
COLOR TELEVISION
Owner’s
Instructions
Record your Model and Serial number here for future reference.
▪ Model _______________ ▪ Serial No. _______________
Accessories
Please make sure the following items are included with your TV.
If any items are missing, contact your dealer.
Remote Control (AA59-00405B)/
AAA Batteries
Owner’s Instructions/
Safety Guide Manual
Warranty Cards/
Registration Card
Viewing the Control Panel
You can control your TV’s basic features, including the on-screen menu.
To use the more advanced features, you must use the remote control.
TX-T2781
TX-T2782
TX-T2082
The product color and shape may vary depending on the model.
➢
1
SOURCE
4
5
CH
Toggles between all the available input sources (TV, AV1,
AV2, Component).
In the on-screen menu, use this button as you would use the
ENTER button on the remote control.
Press to change channels.
In the on-screen menu, use the
would use the ▲ and ▼ buttons on the remote control.
CH
buttons as you
Power Indicator
2
3
MENU
Lights up when you turn the power off.
Press to see an on-screen menu of your TV’s features.
-
-
Power Off: Red
Power On: Off
+ VOL −
Press to increase or decrease the volume.
In the on-screen menu, use the + VOL – buttons as you would
use the ◄ and ► buttons on the remote control.
6
7
Remote Control Sensor
Aim the remote control towards this spot on the TV.
POWER
Press to turn the TV on and off.
English - 3
Viewing the Connection Panel
Use the rear panel jacks to connect A/V components that will be connected continuously, such as VCR or DVD players.
Rear of the TV
Side of the TV
TX-T2781/TX-T2782
TX-T2082
The product color and shape may vary depending on the model.
➢
1
2
3
ANT IN (AIR/CABLE)
Connect to an antenna(air) or cable TV system.
5
6
Headphone
Connect a set of external headphones to this jack for private
listening.
AV OUT
Connect to the audio/video input jacks of a recording VCR.
UPGRADE PORT (USB)
Connect for service and software upgrade.
AV IN 1 / AV IN 2
Video and audio inputs for external devices, such as a
camcorder or VCR.
4
COMPONENT IN
Connect Component video/audio.
English - 4
Remote Control
You can use the remote control up to a distance of about 23 feet from the TV. When using the remote control, always point it
directly at the TV.
This is a special remote control for the visually impaired, and has Braille points on the POWER, Channel, and Volume buttons.
The performance of the remote control may be affected by bright light.
➢
1
2
3
POWER
Turns the TV on and off.
@
#
$
SOURCE
Press to display all of the available
video sources.
NUMERIC BUTTONS
Press to directly select a channel.
INFO
Press to display information on the
TV screen.
–
Press to select additional channels
being broadcast by the same station.
For example, to select channel “54-
3”, press “54”, then press “–” and “3”.
TV/DTV
Press to switch between TV (Analog)
and DTV (Digital) mode.
4
VOL +, VOL –
Press to increase or decrease the
volume.
%
^
&
*
(
CH
, CH
Press to change channels.
EXIT
5
6
MENU
Press to exit from the menu.
Displays the main on-screen menu.
MUTE
UP▲/DOWN▼/LEFT◄/RIGHT►/
ENTER
Use to select on-screen menu items
and change menu values.
Press to temporarily cut off the sound.
P.SIZE
Press to change the screen size.
SLEEP
7
8
9
S.MODE
Press to select the sound mode.
Press to select a preset time interval
for automatic shut off.
P.MODE
Press to select the picture mode.
)
MTS
Press to choose stereo, mono
or Separate Audio Program(SAP
broadcast).
AUTO PROG.
Press to automatically store selected
Air/Cable channels.
a
b
CAPTION
Controls the caption decoder.
0
!
ADD/DEL
Use to store and delete channels
to/from memory.
R.SURF
Press to automatically return to a
preferred channel after a user-preset
time delay.
PRE-CH
Tunes to the previous channel.
c
TURBO
Press to select Turbo sound.
Installing Batteries in the Remote Control
1
2
Lift the cover at the back of the remote control upward as shown in the figure.
Install two AAA size batteries.
Make sure to match the + and – ends of the batteries with the diagram inside the
➢
compartment.
Do not mix battery types, i.e. alkaline and manganese.
3
Replace the cover.
Remove the batteries and store them in a cool and dry place if you won’t be using the
➢
remote control for a long time. The remote control can be used up to about 23 feet from
the TV. (Assuming typical TV usage, the batteries last for about one year.)
English - 5
Connecting VHF and UHF Antennas
Antennas with 300 Ω Flat Twin Leads
If you are using an off-air antenna(such as a roof antenna or “rabbit ears”) that has 300 Ω twin flat leads, follow the directions
below.
1
Place the wires from the twin leads under the screws on a 300-75 Ω adapter(not supplied).
Use a screwdriver to tighten the screws.
1
2
2
Plug the adaptor into the ANT IN (AIR/CABLE) terminal on the back of the TV.
Antennas with 75 Ω Round Leads
Plug the antenna lead into the ANT IN (AIR/CABLE) terminal on the back of the TV.
1
1
Separate VHF and UHF Antennas
If you have two separate antennas for your TV(one VHF and one UHF), you must combine the two antenna signals before
connecting the antennas to the TV. This procedure requires an optional combiner-adaptor(available at most electronics
shops).
1
Connect both antenna leads to the combiner.
1
2
Plug the combiner into the ANT IN (AIR/CABLE) terminal on the back of the TV.
2
Connecting Cable TV
Cable without a Cable Box
1
Plug the incoming cable into the ANT IN (AIR/CABLE) terminal on the back of the TV.
Because this TV is cable-ready, you do not need a cable box to view unscrambled cable
➢
1
channels.
Connecting to a Cable Box that Descrambles All Channels
1
Find the cable that is connected to the ANT OUT terminal on your cable box.
This terminal might be labeled “ANT OUT”, “VHF OUT” or simply, “OUT”.
➢
ANT IN
ANT OUT
2
Connect the other end of this cable to the ANT IN (AIR/CABLE) terminal on the back of the TV.
1
2
Connecting to a Cable Box that Descrambles Some Channels
If your cable box descrambles only some channels(such as premium channels), follow the instructions below. You will need a
two-way splitter, an RF (A/B) switch, and four lengths of Antenna cable. (These items are available at most electronics stores.)
5
1
2
6
Incoming
cable
4
3
TV Rear
Splitter
RF (A/B)
Switch
Cable Box
Cable Box
1
Find and disconnect the cable that is connected to the
ANT IN terminal on your cable box.
5
6
Connect another cable between the other OUT terminal on
the splitter and the A-IN terminal on the RF (A/B) switch.
This terminal might be labeled “ANT IN”, “VHF IN” or
simply, “IN”.
➢
Connect the last Antenna cable between the OUT terminal
on the RF (A/B) switch and the ANT IN (AIR/CABLE)
terminal on the back of the TV.
2
3
Connect this cable to a two-way splitter.
Connect an Antenna cable between an OUT terminal on
the splitter and the IN terminal on the cable box.
After you have made this connection, set the A/B switch to the
“A” position for normal viewing. Set the A/B switch to the “B”
position to view scrambled channels. (When you set the A/B
switch to “B”, you will need to tune your TV to the cable box’s
output channel, which is usually channel 3 or 4.)
4
Connect an Antenna cable between the ANT OUT terminal
on the cable box and the B-IN terminal on the RF(A/B)
switch.
English - 6
Connecting a VCR
Video Connection
These instructions assume that you have already connected your TV to an antenna or a cable TV system(according to the
instructions on page 6). Skip step 1 if you have not yet connected to an antenna or a cable system.
Each VCR has a different back panel configuration.
When connecting a VCR, match the color of the connection terminal to the cable.
➢
1
2
Unplug the cable or antenna from the back of the TV.
Rear of the TV
Connect the cable or antenna to the ANT IN terminal on
the back of the VCR.
VCR
3
Connect an Antenna cable between the ANT OUT terminal
on the VCR and the ANT IN (AIR/CABLE) terminal on the
TV.
4
5
Connect a Video Cable between the VIDEO OUT jack on
the VCR and the AV IN 1 [VIDEO] jack on the TV.
Connect Audio Cables between the AUDIO OUT jacks on
the VCR and the AV IN 1 [L-AUDIO-R] jacks on the TV.
Audio Cable
5
If you have a “mono” (non-stereo) VCR, use a
(Not supplied)
➢
2
Y-connector(not supplied) to hook up to the right and
left audio input jacks of the TV. If your VCR is stereo,
you must connect two cables.
4
3
Video Cable(Not supplied)
Antenna cable(Not supplied)
Also, you can connect to AV IN 2 on the side panel of TV.
➢
Connecting a Camcorder
The side panel jacks on your TV make it easy to connect a camcorder to your TV.
They allow you to view the camcorder tapes without using a VCR.
Each Camcorder has a different back panel configuration.
When connecting a Camcorder, match the color of the connection terminal to the cable.
➢
1
2
Connect a Video Cable between the AV IN 2 [VIDEO] jack
on the TV and the VIDEO OUT jack on the camcorder.
Side of the TV
Connect Audio Cables between the AV IN 2
[L-AUDIO-R] jacks on the TV and the AUDIO OUT jacks
on the camcorder.
1
2
Video Cable(Not supplied)
Camcorder
Audio Cable(Not supplied)
English - 7
Connecting a DVD Player/Set-Top Box
The rear panel jacks on your TV make it easy to connect a DVD player/Set-Top Box.
Each DVD Player/Set-Top Box has a different back panel configuration.
When connecting a DVD Player/Set-Top Box, match the color of the connection terminal to the cable.
➢
1
Connect Component Cables between the COMPONENT
IN [Y, PB, PR] jacks on the TV and the COMPONENT OUT
[Y, PB, PR] jacks on the DVD Player/Set-Top Box.
Rear of the TV
DVD Player/Set-Top Box
2
Connect Audio Cables between the COMPONENT IN
[L-AUDIO-R] jacks on the TV and the AUDIO OUT jacks
on the DVD Player/Set-Top Box.
Component video separates the video into Y(Luminance
(brightness)), PB(Blue), and PR(Red) for enhanced video
quality. Be sure to match the component video and audio
connections.
For example, if connecting the video cable to
COMPONENT IN, connect the audio cable to
COMPONENT IN also.
➢
➢
Audio Cable
(Not supplied)
2
1
Component Cable(Not supplied)
This product is an SD-grade DTV and must be connected
in the resolution of 480i.
If this product is connected in the resolution of 480p, 720p
or 1080i, the screen may be displayed abnormally or may
not be displayed at all.
Connecting an Amplifier/DVD Home Theater - Analog
Each Amplifier/DVD Home Theater has a different back panel configuration.
When connecting an Amplifier/DVD Home Theater, match the color of the connection terminal to the cable.
➢
1
Connect Audio Cables between the AV OUT
[L-AUDIO-R] on the TV and AUDIO IN on the Amplifier/
DVD Home Theater.
Rear of the TV
Amplifier/
DVD Home Theater
When an audio amplifier is connected to the AUDIO OUT
[L-AUDIO-R] terminals: Decrease the volume of the TV,
and adjust the volume level with the Amplifier’s volume
control.
1
Audio Cable(Not supplied)
English - 8
Plug & Play Feature
When the TV is initially powered on, basic settings proceed automatically and
subsequently:
Plug & Play
Start Plug & Play
1
Press the POWER button on the remote control.
The message Start Plug & Play is displayed.
Press the ENTER button, then the Language menu is displayed.
OK
Enter
Exit
2
3
Press the ▲ or ▼ button to select the desired language, then press the ENTER button.
The message Select Home Mode when installing this TV at home. is displayed.
Plug & Play
Language
English
Español
Français
Press the ◄ or ► button to select Shop or Home, then press the ENTER button.
The Check antenna input. menu is displayed.
The default selection is Home.
We recommend setting the TV to Home mode for the best picture in your home
environment.
➢
Move
Enter
Skip
Shop mode is only intended for use in retail environments.
If the unit is accidentally set to Shop mode and you want to return to Dynamic (Home)
mode, press the Volune button and then hold down the MENU button for five seconds
on the TV panel.
Plug & Play
Select Home Mode
when installing this TV
at home.
4
5
6
Make sure that an antenna is connected to the TV.
Press the ENTER button, then the Antenna menu is displayed.
Shop
Home
Move
Enter
Skip
Press the ▲ or ▼ button to select the desired connection.
Press the ENTER button to memorize the channels of the selected connection.
Plug & Play
Press the ENTER button to start.
First analog, then digital channels will be memorized.
Auto Program
Air
Cable
Air+Cable
When selecting Cable TV:
7
8
9
Press the ▲ or ▼ button to select Cable, then press the ENTER button.
The Cable System menu is displayed.
Move
Enter
Skip
Press the ▲/▼/◄/► buttons to select the cable system for analog and digital channels
respectively, then press the ENTER button.
Plug & Play
Auto Program
Cable System
Analog
Start
Press the ENTER button to start. The TV begins memorizing all available channels.
Press the ENTER button to stop.
After all available channels are stored, the Clock Set menu is displayed.
STD
HRC
HRC
IRC
Digital
STD
IRC
When you select Cable or Air+Cable, it also executes “Clearing Scrambled Channels”
simultaneously. See page 15.
➢
Move
Enter
Skip
10 Press the ◄ or ► button to move to the hour or minute.
Set the clock by pressing the ▲ or ▼ button, then press the ENTER button.
Plug & Play
Auto Program in progress
STD 120
11 The message Enjoy your watching. is displayed.
3%
When you have finished, press the ENTER button.
Even if the ENTER button is not pressed, the message will automatically disappear after
several seconds.
➢
Stop
Enter
Skip
If you want to reset this feature...
Scrambled Channels Searched
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the ENTER button.
Press the ENTER button to select Plug & Play.
Plug & Play
2
For further details on setting up options, refer to the top of this page.
Clock Set
-- : -- am
The Plug & Play feature is only available in TV and DTV mode.
➢
Move
Enter
Skip
Enjoy your watching.
OK
English - 9
Memorizing the Channels
Your TV can memorize and store all of the available channels for both air and cable
Channel
channels. After the available channels are memorized, use the CH
and CH
button
Antenna
Auto Program
Clear Scrambled Channel
Add/Delete
Fine Tune
:
Air
Cable
to scan through the channels. This eliminates the need to change channels by entering
the channel digits. There are three steps for memorizing channels: selecting a broadcast
source, memorizing the channels(automatic) and adding or deleting channels(manual).
Name
Signal Strength
Selecting the Video Signal-source
Before your television can begin memorizing the available channels, you must specify the
type of signal source that is connected to the TV(i.e. an air or a cable system).
Move
Enter
Return
Channel
Antenna
Auto Program
Clear Scrambled Channel
Add/Delete
Fine Tune
Name
Signal Strength
: Air
►
►
►
►
►
►
►
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the ENTER button.
2
Press the ENTER button select Antenna.
Press the ▲ or ▼ button to select Air or Cable, then press the ENTER button.
Storing Channels in Memory (Automatic Method)
Move
Enter
Return
3
4
5
Press the ▲ or ▼ button to select Auto Program, then press the ENTER button.
Auto Program
Press the ▲ or ▼ button to select the antenna connection, then press the ENTER button.
Air
Cable
Air+Cable
Press the ENTER button to start.
First analog, then digital channels will be memorized.
When selecting Cable TV:
Move
Enter
Return
7
Press the ▲ or ▼ button to select Cable, then press the ENTER button.
The Cable System menu is displayed.
Auto Program
8
Press the ▲/▼/◄/► buttons to select the cable system for analog and digital channels
respectively, then press the ENTER button.
Cable System
Analog
Start
STD, HRC, and IRC identify various types of cable TV systems. Contact your local cable
company to identify the type of cable system that exists in your particular area.
At this point the signal source has been selected.
STD
Digital
HRC
HRC
IRC
➢
STD
IRC
Move
Enter
Return
9
Press the ENTER button to start.
The TV begins memorizing all available channels.
Press the ENTER button to stop.
Auto Program
Auto Program in progress
STD 120
When you select Cable or Air+Cable it also executes “Clearing Scrambled Channels”
➢
simultaneously. See page 15.
3%
This TV can receive Digital HD (High Definition) signals, but converts them to SD (Standard
Definition) for viewing.
➢
Stop
Return
Enter
You can also press the AUTO PROG. button on the remote control to bring up the Auto
Scrambled Channels Searched
Program menu.
English - 10
To Select the Source
Use to select TV or other external input sources such as DVD players, VCRs, etc. connected
to the TV.
Source List
TV
DTV
AV1
AV2
1
Press the MENU button to display the menu.
Press the ENTER button to select Input.
- - - -
- - - -
- - - -
Component
2
Press the ENTER button to select Source List.
Press the ▲ or ▼ button to select signal source, then press the ENTER button.
You can choose between the following sets of jacks: TV, AV1, or Component on the
TV’s rear panel and AV2 on the TV’s side panel.
Move
Enter
Return
➢
Press the SOURCE button on the remote control to view an external signal source.
In TV(Analog) mode: TV → AV1 → AV2 → Component
In DTV(Digital) mode: DTV → AV1 → AV2 → Component
To check the input signals displayed, press the INFO button on the remote control.
➢
To Edit the Input Source Name
Name the external device connected to the input jacks to make your input source selection
easier.
Edit Name
AV1
AV2
Component
: -
----
: -
VCR
: -
DVD
1
Press the MENU button to display the menu.
Press the ENTER button to select Input. Press the ▲ or ▼ button to select Edit Name, then
press the ENTER button.
Cable STB
Sat. STB
AV Receiver
DVD Receiver
▼
2
3
Press the ▲ or ▼ button to select AV1, AV2, or Component input jack, then press the
ENTER button.
Move
Enter
Return
Press the ▲ or ▼ button to select VCR, DVD, Cable STB, Sat. STB, AV Receiver,
DVD Receiver, Game, Camcorder, or DVD Combo input source, then press the ENTER
button.
Press the EXIT button to exit.
Using Automatic Picture Settings
Your TV has four automatic picture settings (“Dynamic”, “Standard”, “Movie”, “Custom”)
that are preset at the factory.
Mode
Mode
:
Dynamic
You can activate a Picture Setting by making a selection from the menu.
Contrast
Brightness
Sharpness
Color
Tint
Color Tone
Reset
Standard
50
Movie
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Picture, then press the ENTER button.
:
Custom
: G 50 R 50
: Cool1
2
Press the ENTER button to select Mode.
Press the ENTER button again. Press the ▲ or ▼ button to select the Dynamic, Standard,
Movie, or Custom picture setting, then press the ENTER button.
Move
Enter
Return
Choose Dynamic for viewing the TV during the day or when there is bright light in the
room.
Choose Standard for general TV watching mode.
Choose Movie when watching movies.
Choose Custom if you want to adjust the settings according to personal preference.
Press the P.MODE button on the remote control to select one of the standard picture
settings.
Continued...
English - 11
3
4
Press the ▲ or ▼ button to select Contrast, Brightness, Sharpness, Color, or Tint, then
press the ENTER button.
Press the ◄ or ► button to decrease or increase the value of a particular item.
Contrast
Mode
100
You can not adjust the Tint in DTV, AV, or Component mode.
Press the ENTER button to return to Mode.
➢
Mode
5
6
7
: Dynamic
Press the ▲ or ▼ button to select Color Tone, then press the ENTER button.
Press the ▲ or ▼ button to select Cool2, Cool1, Normal, Warm1, or Warm2, then press the
ENTER button.
Contrast
:
:
:
:
100
50
Brightness
Sharpness
Color
Tint
Color Tone
Reset
Cool2
Cool1
Normal
:
Warm1
:
Resetting the Picture Settings to the Factory Defaults
8
Warm2
Press the ▲ or ▼ button to select Reset, then press the ENTER button.
Press the EXIT button to exit.
Move
Enter
Return
Each picture mode can be reset.
➢
Changing the Screen Size
You can select the picture size which best corresponds to your viewing requirements.
Picture
Mode
Size
Digital NR
Tilt
: Dynamic
:
Zoom
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Picture, then press the ENTER button.
Normal
:
0
2
3
Press the ▲ or ▼ button to select Size, then press the ENTER button.
Press the ▲ or ▼ button to select the screen format you want, then press the ENTER button.
Press the EXIT button to exit.
Move
Enter
<TV Mode>
Return
Normal: Sets the picture to 4:3 normal mode.
Zoom: Magnifies the size of the picture on the screen.
Wide: Sets the picture to 16:9 wide mode.
Press the P.SIZE button on the remote control repeatedly to change the picture size.
Changing the screen size is determined by the TV signal type being viewed. Analog and
Digital signals display different screen sizes.
➢
➢
Analog TV Mode: Switching between Normal and Zoom is possible. The TV must
be connected to Analog Air/Cable, or to an external device via Composite, S-Video or
Component to view these screen sizes.
Digital TV Mode: Switching between Normal and Wide is possible. The TV must be
connected to Digital Air/Cable to view these screen sizes
To identify whether the current mode is TV Mode or DTV Mode, press the INFO button on
the remote control. To switch between Analog and Digital Air/Cable mode, press the TV/DTV
button on the remote.
Analog TV Mode
Digital TV Mode
Normal
Zoom
Normal
Wide
Digital Noise Reduction
If the signal received by the television is weak, you can activate this feature to reduce any
static and ghosting that may appear on the screen.
Picture
Mode
Size
Digital NR
Tilt
: Dynamic
: Normal
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Picture, then press the ENTER button.
Off
:
On
:
2
3
Press the ▲ or ▼ button to select Digital NR, then press the ENTER button.
Press the ▲ or ▼ button to select Off or On, then press the ENTER button.
Press the EXIT button to exit.
Move
Enter
Return
English - 12
Tilt (TX-T2781/TX-T2782 only)
Due to the Earth’s magnetic field there may be some minor image tilt depending on the TV’s
location. When this occurs, follow the steps below.
Picture
Mode
Size
Digital NR
Tilt
: Dynamic
: Normal
: On
►
►
►
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Picture, then press the ENTER button.
:
+ 2
2
3
Press the ▲ or ▼ button to select Tilt, then press the ENTER button.
Press the ◄ or ► button to adjust screen tilt.
Press the EXIT button to exit.
Move
Adjust
Return
Using Automatic Sound Settings
Your TV has automatic sound settings (“Standard”, “Music”, “Movie”, “Speech”, and
“Custom”) that are preset at the factory. Or, you can select “Custom”, which automatically
recalls your personalized sound settings.
Sound
Mode
Equalizer
MTS
Auto Volume
Pseudo Stereo
Turbo Plus
: Standard
Music
: Movie
Speech
Custom
: Off
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Sound, then press the ENTER button.
2
Press the ENTER button to select Mode. Press the ▲ or ▼ button to select Standard, Music,
Movie, Speech, or Custom sound setting, then press the ENTER button.
Move
Enter
Return
Press the EXIT button to exit.
Choose Standard for the standard factory settings.
Choose Music when watching music videos or concerts.
Choose Movie when watching movies.
Choose Speech when watching a show that is mostly dialog (i.e., news).
Choose Custom to recall your personalized settings (see “Customizing the Sound”).
Press the S.MODE button on the remote control repeatedly to select one of the standard
sound settings.
Customizing the Sound
The sound settings can be adjusted to suit your personal preference. (Alternatively, you
can use one of the “automatic” settings.)
Equalizer
R
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Sound, then press the ENTER button.
L
2
3
Press the ▲ or ▼ button to select Equalizer, then press the ENTER button.
100 300 1K
Adjust
3K 10K
Return
Press the ◄ or ► button to select a particular frequency to adjust.
Press the ▲ or ▼ button to increase or decrease the level of the particular frequency, then
press the ENTER button.
Move
Press the EXIT button to exit.
R/L Sound Balance Adjustment:
To adjust the sound balance of the R/L speakers.
Bandwidth Adjustment(100, 300, 1K, 3K, 10K):
➢
➢
To adjust the level of different bandwidth frequencies.
If you make any changes to the equalizer settings, the sound mode is automatically switched to the Custom.
English - 13
Choosing a Multi-Channel Sound (MTS) Track - Digital
The digital-TV transmission system is capable of simultaneous transmission of many audio
tracks (for example, simultaneous translations of the program into foreign languages).
The availability of these additional “multitracks” depends upon the program.
Sound
Mode
Equalizer
Pref. lang.
Auto Volume
Pseudo Stereo
Turbo Plus
: Custom
English
Spanish
French
: Off
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Sound, then press the ENTER button.
2
3
Press the ▲ or ▼ button to select Pref. lang., then press the ENTER button.
Move
Enter
Return
Press the ▲ or ▼ button to choose the language (English, Spanish, or French) you want,
then press the ENTER button.
Press the EXIT button to exit.
Press the MTS button on the remote control to listen in a language other than the
preferred language.
Choosing a Multi-Channel Sound (MTS) Track - Analog
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Sound, then press the ENTER button.
Sound
Mode
Equalizer
MTS
Auto Volume
Pseudo Stereo
Turbo Plus
: Custom
: Mono
Stereo
SAP
2
3
Press the ▲ or ▼ button to select MTS, then press the ENTER button.
Press the ▲ or ▼ button to select a setting you want, then press the ENTER button.
Press the EXIT button to exit.
: Off
Move
Enter
Return
Choose Mono for channels that are broadcasting in mono, or if you are having difficulty
receiving a stereo signal.
Choose Stereo for channels that are broadcasting in stereo.
Choose SAP to listen to the Separate Audio Program, which is usually a foreign
language translation.
Press the MTS button on the remote control repeatedly to select Mono, Stereo, or SAP.
Automatic Volume Control
Sound
Reduces the differences in volume level among broadcasters.
Mode
Equalizer
MTS
Auto Volume
Pseudo Stereo
Turbo Plus
: Custom
: Stereo
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Sound, then press the ENTER button.
:
Off
:
On
2
3
Press the ▲ or ▼ button to select Auto Volume, then press the ENTER button.
Press the ▲ or ▼ button to select On or Off, then press the ENTER button.
Press the EXIT button to exit.
: Off
Move
Enter
Return
English - 14
Using Pseudo Stereo
“Pseudo Stereo” converts a mono sound signal into two identical left and right channels.
Once the “Pseudo Stereo” is set to “On” or “Off”, the setting is applied to sound effects
such as “Standard”, “Music”, “Movie”, and “Speech”.
Sound
Mode
Equalizer
MTS
Auto Volume
Pseudo Stereo
Turbo Plus
: Custom
: Stereo
: Off
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Sound, then press the ENTER button.
:
Off
:
On
2
3
Press the ▲ or ▼ button to select Pseudo Stereo, then press the ENTER button.
Press the ▲ or ▼ button to select On or Off, then press the ENTER button.
Press the EXIT button to exit.
Move
Enter
Return
Using Turbo Plus
“Turbo Plus” emphasizes the bass and treble frequencies to add fullness to the sound.
Sound
Mode
Equalizer
MTS
Auto Volume
Pseudo Stereo
Turbo Plus
: Custom
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Sound, then press the ENTER button.
: Stereo
: Off
: Off
2
3
Press the ▲ or ▼ button to select Turbo Plus, then press the ENTER button.
Press the ▲ or ▼ button to select On or Off, then press the ENTER button.
Press the EXIT button to exit.
:
Off
On
Move
Enter
Return
Press the TURBO button on the remote control repeatedly to select On or Off.
Clearing Scrambled Channels - Digital
The Clear Scrambled Channel function is used to filter out scrambled channels after Auto
Program is completed.
It removes the scrambled channels from the list by tuning the digital cable channels.
This process may take up to 20~30 minutes.
Channel
Antenna
Auto Program
: Cable
►
►
►
►
►
►
►
Clear Scrambled Channel
Add/Delete
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the ENTER button.
Fine Tune
Name
Signal Strength
2
Press the ▲ or ▼ button to select Clear Scrambled Channel, then press the ENTER button.
It searches scrambled channels, which are to be removed from the list.
Move
Enter
Return
To stop searching scrambled channels;
Press the ▼ button to select Stop, then press the ENTER button.
Press the ◄ button to select Yes, then press the ENTER button.
Clear Scrambled Channel
Removing Scrambled Channel.
3
When the scrambled channel searching is completed, press the ENTER button.
Press the EXIT button to exit.
DTV STD 50-1
60%
Stop
Return
Enter
Adding and Erasing Channels - Analog
You can add or delete a channel to display the channels you want.
Add/Delete
▲ More
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the ENTER button.
Press the ▲ or ▼ button to select Add/Delete, then press the ENTER button.
Press the ▲ or ▼ button to select the desired channel, then press the ENTER button.
Press the ▲ or ▼ button to select Deleted or Added, then press the ENTER button.
Press the EXIT button to exit.
Air
Air
Air
Air
Air
2
3
4
5
6
:
Deleted
:
Added
2
3
4
: Deleted
: Deleted
: Deleted
▼ More
Move
Enter
Return
Press the ADD/DEL button on the remote control. Press the CH
and CH
button to
select the channel to be added or deleted, then press the ENTER button.
English - 15
Adding and Erasing Channels - Digital
You can add or delete a DTV channel to display the DTV channels you want.
Add/Delete
Delete
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the ENTER button.
DTV
2
3
Press the ▲ or ▼ button to select Add/Delete, then press the ENTER button.
Air 50-1
Added
Press the CH
or CH
button to select the desired channel, then press the ENTER
button and select Delete or Add.
Press the EXIT button to exit.
Return
Ch.Change
Enter
Press the ADD/DEL button on the remote control. Press the CH
and CH
button to
select the channel to be added or deleted, then press the ENTER button.
Fine Tuning Analog Channels - Analog
Use fine tuning to manually adjust a particular channel for optimal reception.
Fine Tune
Reset
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the ENTER button.
Air 3 ✽
+ 2
2
3
4
Press the ▲ or ▼ button to select Fine Tune, then press the ENTER button.
Press the ◄ or ► button to adjust the fine tuning.
Move
Adjust
Return
To store the fine tuning setting in the TV’s memory, press the ENTER button.
To reset the fine tuning setting, press the ▼ button to select Reset, then press the ENTER
button.
Press the EXIT button to exit.
Only analog TV channels can be fine tuned.
“*” will appear next to the number of fine-tuned channels.
➢
Labeling Channels - Analog
Channels can be labeled so that their call letters appear whenever the channel is selected.
Name
▲ More
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the ENTER button.
Press the ▲ or ▼ button to select Name, then press the ENTER button.
Air
Air
Air
Air
Air
2
: A
3
4
5
6
: - - - -
: - - - -
: - - - -
: - - - -
2
3
Press the ▲ or ▼ button to select the channel to be assigned a new name, then press the
ENTER button.
▼ More
Move
Adjust
Return
Press the ▲ or ▼ button to select a letter, a number or a blank(Results in this sequence: A~Z,
0~9, blank, , -). Press the ► button to switch to the next field, which will be selected. Select a
*
second letter or digit by pressing the ▲ or ▼ button, as above. Repeat the process to select
the last two digits. When you have finished, press the ENTER button to assign the new name.
Press the EXIT button to exit.
The names of digital broadcasting channels are automatically assigned and thus cannot
➢
be assigned by users.
If you add or delete the TV channel, the corresponding label information will also be
added or deleted.
English - 16
Checking the Digital-Signal Strength - Digital
Unlike analog channels, which can vary in reception quality from “snowy” to clear,
digital(HDTV) channels have either perfect reception quality or you will not receive them at
all. So, unlike analog channels, you cannot fine tune a digital channel. You can, however,
adjust your antenna to improve the reception of available digital channels.
Signal Strength
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Channel, then press the ENTER button.
OK
2
Press the ▲ or ▼ button to select Signal Strength, then press the ENTER button.
If the signal strength meter indicates that the signal is weak, physically adjust your antenna
to increase the signal strength. Continue to adjust the antenna until you find the best position
with the strongest signal.
Enter
Return
Press the EXIT button to exit.
You can also press the ENTER button to select OK, then press the EXIT button to exit.
Using the R.Surf Feature
This feature allows you to set the TV to return to a particular channel after a certain amount
of time. For example, you may be watching a channel when commercials start. You can set
the R.Surf to “5 minutes”, then switch channels. After 5 minutes, the TV will return to the
original channel. To use the R.Surf feature:
1
While you are watching the channel to which you want to return, press the R.SURF button.
The Surf Off is displayed.
2
Press the R.SURF button again to set the timer in thirty second intervals, up to five minutes.
The time will start decreasing while you are setting up the timer, and will reset after
5 minutes has passed or you turn it off.
➢
3
The time you set will begin counting down on the screen.
When the time runs out, the TV will return to the channel you were watching when you set the
timer.
Surf
00: 29
Selecting a Menu Language
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the ENTER button.
Language
English
Español
Français
2
3
Press the ▲ or ▼ button to select Language, then press the ENTER button.
Press the ▲ or ▼ button to select the appropriate language: English, Español or Français,
then press the ENTER button.
Press the EXIT button to exit.
Move
Enter
Return
English - 17
Setting the Time
Setting the clock is necessary in order to use the various timer features of the TV.
Also, you can check the time while watching the TV. (Just press the INFO button.)
Time
12 : 00 am
Clock
Sleep Timer
On Timer
Off Timer
: Off
►
-- : -- am Off
-- : -- am Off
1
Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then
press the ENTER button. Press the ▲ or ▼ button to select Time, then press the ENTER
button.
On Timer Source
On Timer Antenna
On Timer Channel
On Timer Volume
:
:
:
TV
Air
►
►
3
2
3
Press the ENTER button to select Clock.
:
10
Move
Adjust
Return
Press the ◄ or ► button to move to the hour or minute.
Set the clock by pressing the ▲ or ▼ button, then press the ENTER button.
Press the EXIT button to exit.
The current time will appear every time you press the INFO button.
➢
Setting the Sleep Timer
Time
09 : 30 am
Off
The Sleep Timer automatically shuts off the TV after a preset time(from 30 to 180 minutes).
Clock
Sleep Timer
On Timer
Off Timer
:
1
Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then
press the ENTER button. Press the ▲ or ▼ button to select Time, then press the ENTER
button.
30
-- : -
60
-- : -
90
On Timer Source
On Timer Antenna
On Timer Channel
On Timer Volume
120
150
2
3
Press the ▲ or ▼ button to select Sleep Timer, then press the ENTER button.
180
:
10
Move
Enter
Return
Press the ▲ or ▼ button to select the minutes.
To cancel the set sleep timer:
Press the ▲ or ▼ button to select Off, then press the ENTER button.
Press the EXIT button to exit.
Press the SLEEP button on the remote control until the appropriate time interval appears
(any of the preset values from 30 min to 180 min).
Setting the On/Off Timer
Time
Clock
09 : 30 am
: Off
12 : 00 am Off
-- : -- am Off
Use this feature to set the TV to turn on or off at a desired time.
You must set the clock first.
Sleep Timer
On Timer
Off Timer
On Timer Source
On Timer Antenna
On Timer Channel
On Timer Volume
►
1
Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then
press the ENTER button. Press the ▲ or ▼ button to select Time, then press the ENTER
button.
:
:
:
TV
Air
►
►
3
:
10
Move
Adjust
Return
2
3
Press the ▲ or ▼ button to select On Timer, then press the ENTER button.
Time
Press the ▲ or ▼ button to set the hour, then press the ► button to move to the next step.
Set other items using the same method as above.
Clock
09 : 30 am
: Off
06 : 30 am On
11 : 00 pm On
Sleep Timer
On Timer
Off Timer
On Timer Source
On Timer Antenna
On Timer Channel
On Timer Volume
►
When finished, press the MENU button to return.
➢
:
:
:
TV
Air
►
►
3
4
5
Press the ▲ or ▼ button to select Off Timer, then press the ENTER button.
Press the ▲ or ▼ button to set the hour, then press the ► button to move to the next step.
Set other items using the same method as above.
:
10
Move
Adjust
Return
When finished, press the MENU button to return.
➢
Auto Power Off
➢
When you set the timer “On”, the TV will eventually turn off if no controls are operated for 3
hours after the TV was turned on by timer. This function is only available in timer “On” mode
and prevents overheating, which may occur if a TV is on for too long time.
Setting the Preferred Option
The preferred TV source, antenna, channel and volume can be set for when the timer
automatically turns on the TV.
Time
Clock
09 : 30 am
: Off
06 : 30 am On
11 : 00 pm On
Sleep Timer
On Timer
Off Timer
On Timer Source
On Timer Antenna
On Timer Channel
On Timer Volume
6
7
8
Press the ▲ or ▼ button to select On Timer Source, then press the ENTER button.
Press the ▲ or ▼ button to select TV or DTV, then press the ENTER button.
:
:
:
TV
DTV
Press the ▲ or ▼ button to select On Timer Antenna, then press the ENTER button.
Press the ▲ or ▼ button to select Air or Cable, then press the ENTER button.
3
:
10
Return
Move
Enter
Press the ▲ or ▼ button to select On Timer Channel or On Timer Volume.
Press the ◄ or ► button to select the desired channel or adjust volume level.
Press the EXIT button to exit.
English - 18
Viewing Closed Captions(On-Screen Text Messages) - Digital
The Digital Captions function operates on digital channels.
Caption
Caption
Mode
Options
:
Default
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the ENTER button.
Service1
:
Service2
Service3
Service4
Service5
Service6
CC1
2
3
Press the ▲ or ▼ button to select Caption, then press the ENTER button.
Press the ENTER button to select Caption. Press the ▲ or ▼ button to select On, then press
the ENTER button.
▼
Move
Enter
Return
4
Press the ▲ or ▼ button to select Mode, then press the ENTER button.
Press the ▲ or ▼ button to select the submenu (Default, Service1~Service6, CC1~CC4, or
Text1~Text4) you want, then press the ENTER button.
Options
Size
Font Style
Fore Color
: Default
: Default
: Default
►
►
►
►
►
►
5
6
Press the ▲ or ▼ button to select Options, then press the ENTER button.
Back Color : Default
Fore Opacity : Default
Back Opacity : Default
Return to Default
Press the ENTER button to select Size. Press the ▲ or ▼ button to select the desired caption
option, then press the ENTER button. Press the ▲ or ▼ button to select the desired sub-
menu options(see options below), then press the ENTER button.
Move
Enter
Return
Press the EXIT button to exit.
The availability of captions depends on the program being broadcast.
Default means to follow the standard set by the broadcaster.
Fore(Foreground) and Back cannot be set to have the same color.
Fore Opacity and Back Opacity cannot be both set to Transparent.
➢
Size: This option consists of Default, Small, Standard, and Large. The default is Standard.
Font Style: This option consists of Default, Style0 ~ Style7. You can change the font you want.
The default is Style0.
Fore Color: This option consists of Default, White, Black, Red, Green, Blue, Yellow, Magenta, and Cyan. You can change the
color of the letter. The default is White.
Back Color: This option consists of Default, White, Black, Red, Green, Blue, Yellow, Magenta, and Cyan. You can change the
background color of the caption. The default is Black.
Fore Opacity: This option consists of Default, Solid, Flashing, Translucent, and Transparent.
You can change the opacity of the letter.
Back Opacity: This option consists of Default, Solid, Flashing, Translucent, and Transparent.
You can change the background opacity of the caption.
Return to Default: This option sets each of Size, Font Style, Fore Color, Back Color, Fore Opacity, and Back Opacity to its
factory default.
You can also press the CAPTION button on the remote control to select Captions On or
Off.
Viewing Closed Captions(On-Screen Text Messages) - Analog
The Analog Caption function operates in either analog TV channel mode or external signal
Caption
mode. (Depending on the broadcasting signal, the Analog Caption function may operate on
digital channels.)
Caption
Mode
Channel
Field
: O
Off
:
On
: 1
: 1
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the ENTER button.
2
3
Press the ▲ or ▼ button to select Caption, then press the ENTER button.
Move
Enter
Return
Press the ENTER button to select Caption.
Press the ▲ or ▼ button to select On, then press the ENTER button.
Misspellings and unusual characters sometimes occur during closed caption
transmissions, especially those of live events. There may be a small delay before captions
appear when you change channels. These are not malfunctions of the TV.
➢
4
Press the ▲ or ▼ button to select Mode, then press the ENTER button.
Press the ▲ or ▼ button to select the Caption or Text, then press the ENTER button.
In Caption mode, captions appear at the bottom of the screen, and they usually cover
only a small portion of the picture.
➢
In Text mode, information unrelated to the program, such as news or weather, is
displayed. Text often covers a large portion of the screen.
Continued...
English - 19
5
Depending on the particular broadcast, it might be necessary to make changes to Channel
and Field. Press the ▲ or ▼ button to select Channel or Field, then press the ENTER button.
Press the ▲ or ▼ button to select 1 or 2, then press the ENTER button.
Different channels and fields display different information:
➢
Field 2 carries additional information that supplements the information in Field 1.
(For example, Channel 1 may have subtitles in English, while Channel 2 has subtitles in
Spanish.)
Press the EXIT button to exit.
You can also press the CAPTION button on the remote control to select Captions On or
Off.
Setting the Blue Screen Mode
If no signal is being received or the signal is very weak, a blue screen automatically
replaces the noisy picture background. If you wish to continue viewing the poor picture,
you must set the “Blue Screen” mode to “Off”.
Setup
Plug & Play
Language
Time
: English
Caption
Blue Screen
Melody
V-Chip
Software upgrade
1
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the ENTER button.
:
:
On
Off
2
Press the ▲ or ▼ button to select Blue Screen, then press the ENTER button.
Press the ▲ or ▼ button to select On or Off, then press the ENTER button.
Move
Enter
Return
Press the EXIT button to exit.
Setting the On/Off Melody
A melody sound can be set to come on when the TV is powered On or Off.
Setup
Plug & Play
Language
Time
Caption
Blue Screen
Melody
1
2
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the ENTER button.
: English
: Off
: Off
On
Press the ▲ or ▼ button to select Melody, then press the ENTER button.
Press the ▲ or ▼ button to select On or Off, then press the ENTER button.
V-Chip
Software upgrade
Move Enter
Press the EXIT button to exit.
Return
TRADEMARK & LABEL LICENSE NOTICE
Manufactured under license from Dolby Laboratories. Dolby and the double-D
symbol are trademarks of Dolby Laboratories.
Using the V-Chip
U.S.A Only
This product is covered by the following U.S. patents : US4,930,158 US4,930,160
The V-Chip feature automatically locks out programs that are deemed inappropriate for children.
The user must enter a PIN(Personal ID number) before any of the V-Chip restrictions are set up or changed.
How to Enable/Disable the V-Chip
V-Chip
1
2
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the ENTER button.
V-Chip Lock
Change PIN
:
Off
On
Press the ▲ or ▼ button to select V-Chip, then press the ENTER button.
The message Enter PIN will appear. Enter your 4 digit PIN.
The default PIN of a new TV set is “0-0-0-0”.
➢
3
The V-Chip screen will appear. To enable the V-Chip feature, press the ENTER button so that
the V-Chip Lock field is On. (Pressing the ▲ or ▼ button will alternate between On and Off.)
Move
Enter
Return
Continued...
English - 20
Setting Up Your Personal ID Number(PIN)
V-Chip
4
5
Press the ▲ or ▼ button to select Change PIN, then press the ENTER button.
V-Chip Lock
TV Parental Guidelines
MPAA Rating
Downloadable U.S. Rating
Change PIN
: On
►
►
►
►
►
The Enter New PIN screen will appear. Choose any 4 digits for your PIN and enter them.
As soon as the 4 digits are entered, the Confirm New PIN screen appears. Re-enter the
same 4 digits. When the Confirm screen disappears, your PIN has been memorized.
If you forget the PIN, press the remote control buttons in the following sequence, which resets
the pin to 0-0-0-0 : Power Off → MUTE → 8 → 2 → 4 → Power On.
➢
Move
Enter
Return
<for USA models only >
How to Set up Restrictions Using the ‘TV Parental Guidelines’
V-Chip
First, set up a personal identification number(PIN), and enable the V-Chip.
(See previous section.)
Parental restrictions can be set up using either of two methods:
The TV guidelines or the MPAA rating.
V-Chip Lock
TV Parental Guidelines
MPAA Rating
Canadian English
Canadian French
Downloadable U.S. Rating
Change PIN
: On
►
►
►
►
►
►
►
6
7
Press the ▲ or ▼ button to select TV Parental Guidelines, then press the ENTER button.
Press the ▲ or ▼ button to select one of the six aged based categories:
Move
Enter
Return
TV-Y: Young children.
TV-Y7: Children 7 and
TV-PG: Parental guidance.
TV-14: Viewers 14 and
<for Canada models only>
over.
over.
TV-G: General audience.
TV-MA: Mature audience.
TV Parental Guidelines
ALL FV
B
V
S
L
D
TV-Y
8
Press the ► button. Press the ▲ or ▼ button to select B or U. (U: Unblocked, B: Blocked)
Press the MENU button to save. To select a different TV-Rating, press the ▲ or ▼ button and
then repeat the process.
TV-Y7
TV-G
B
U
U
U
U
B
TV-PG
TV-14
TV-MA
U
U
U
U
U
U
U
U
U
U
U
The TV-Y, TV-Y7, TV-G, TV-PG, TV-14 and TV-MA have additional options.
➢
B: Blocked
U: Unblocked
See the next step to change any of the following sub-ratings.
Move
Adjust Return
FV: Fantasy violence.
D: Sexually suggestive dialog.
L: Adult language.
S: Sexual situation.
V: Violence.
The V-Chip will automatically block certain categories that are “more restrictive”. For example, if you block TV-Y category, then
TV-Y7 will automatically be blocked. Similarly, if you block the TV-G category, then all the categories in the “young adult” group
will be blocked (TV-G, TV-PG, TV-14, and TV-MA). The sub-ratings (D, L, S, V) work together similarly. (See next section.)
➢
9
How to set the FV, V, S, L, and D sub-ratings. First, select one of these TV-Ratings: TV-Y, TV-Y7, TV-G, TV-PG, TV-14, or TV-MA
(See Step 7), and press the ► button. The B will be displayed for each sub-rating. While B is selected, press the ► button to go to
a sub rating. Press the ▲ or ▼ to block the sub rating. Press the MENU button to save. To select a different TV-Rating, press the
▲ or ▼ button and then repeat the process.
The V-chip will automatically block certain categories that are “more restrictive”.
For example, if you block L sub-rating in TV-PG, then the L sub-ratings in TV-14 and TV-MA will automatically be blocked.
➢
These categories consist of two separate groups: TV-Y and TV-Y7 (young children through age 7), and TV-G through TV-MA
(everybody else). The restrictions for these two groups work independently: If a household includes very young children as well as
young adults, the TV guidelines must be set up separately for each age group.
➢
How to Set up Restrictions Using the MPAA Ratings: G, PG, PG-13, R, NC-17, X, NR
The MPAA rating system uses the Motion Picture Association of America (MPAA) system, and its main application is for
movies. When the V-Chip lock is on, the TV will automatically block any programs that are coded with objectionable ratings
(either MPAA or TV-Ratings).
10 Press the ▲ or ▼ button to select MPAA Rating, then press the ENTER button.
MPAA Rating
G
B
11 Press the ▲ or ▼ button to select an appropriate restriction. Press the ► button, then press
the ▲ or ▼ button to select B or U (U: Unblocked, B: Blocked).
Press the MENU button to save.
PG
B
PG-13
B
R
B
NC-17
B
X
B
G: General audience(no restriction).
PG: Parental guidance suggested.
PG-13: Parents strongly cautioned.
R: Restricted. Children under 17 should be accompanied by an adult.
NC-17: No children under age 17.
X: Adults only.
NR
U
B: Blocked
U: Unblocked
Move
Adjust
Return
NR: Not rated.
The V-Chip will automatically block any category that is “more restrictive”.
For example, if you block the PG-13 category, then R, NC-17, and X will automatically be blocked also.
➢
Continued...
English - 21
How to Set up Restrictions Using the ‘Canadian English’ (for Canada Models)
Canadian English
12 Press the ▲ or ▼ button to select Canadian English, then press the ENTER button.
E
B
C
U
13 Press the ▲ or ▼ button to select an appropriate restriction. Press the ► button.
Press the ▲ or ▼ button to select B or U (U: Unblocked, B: Blocked).
Press the MENU button to save.
C8+
U
G
U
PG
U
14+
U
18+
U
E: Exempt programming includes...news, sports, documentaries and other information
programming, talk shows, music videos, and variety programming.
C: Programming intended for children under age 8.
C8+: Programming generally considered acceptable for children 8 years and over to
watch on their own.
B: Blocked
U: Unblocked
Move
Adjust
Return
G: General programming, suitable for all audiences.
PG: Parental guidance.
14+: Programming contains themes or content which may not be suitable for viewers
under the age of 14.
18+: Adult programming.
The V-Chip will automatically block any category that is “more restrictive”.
For example, if you block G category, then PG, 14+, and 18+ will automatically be blocked also.
➢
How to Set up Restrictions Using the ‘Canadian French’ (for Canada Models)
14 Press the ▲ or ▼ button to select Canadian French, then press the ENTER button.
Canadian French
E
G
B
U
U
U
U
U
15 Press the ▲ or ▼ button to select a appropriate restriction. Press the ► button.
Press the ▲ or ▼ button to select B or U (U: Unblocked, B: Blocked).
Press the MENU button to save.
8 ans+
13 ans+
16 ans+
18 ans+
E: Exempt programming includes...news, sports, documentaries and other information
programming, talk shows, music videos, and variety programming.
G: General.
B: Blocked
Move
U: Unblocked
Adjust
Return
8 ans+: Not recommended for young children.
13 ans+: Programming may not be suitable for children under the age of 13.
16 ans+: Programming is not suitable for children under the age of 16.
18 ans+: Programming restricted to adults.
The V-Chip will automatically block any category that is “more restrictive”.
For example, if you block 8 ans+ category, then 13 ans+, 16 ans+, and 18 ans+ will automatically be blocked also.
➢
Using the V-Chip for Digital channels
Parental restriction information can be used while watching DTV channels.
V-Chip
V-Chip Lock
TV Parental Guidelines
MPAA Rating
Canadian English
Canadian French
Downloadable U.S. Rating
Change PIN
: On
►
►
►
►
►
►
►
16 Press the ▲ or ▼ button to select Downloadable U.S. Rating, then press the ENTER button.
If information is not downloaded from the broadcasting station, the Downloadable
U.S. Rating menu is deactivated.
➢
Parental restriction information is automatically downloaded while watching DTV
channels. It may take several seconds.
The Downloadable U.S. Rating menu is available for use after information is
downloaded from the broadcasting station. However, depending on the information
from the broadcasting station, it may not be available for use.
Move
Enter
Return
The number of
current rating title
17 Press the ▲ or ▼ button to select an appropriate restriction. Press the ENTER button to
Rating title
activate the restriction selected. The
(Lock) symbol is indicated.
Press the EXIT button to exit.
Downloadable U.S. Rating
Allow All: Press to unlock all TV ratings.
Humor Level
►
1/ 2
➢
Block All: Press to lock all TV ratings.
NV
MV
V
VV
EV
Allow All
Block All
Parental restriction levels differ depending on the broadcasting station.
The default menu name and Downloadable US rating changes depending on the
downloaded information.
Even if you set the On-screen display to your desired language, the Downloadable
U.S. Rating menu will appear in English only.
Move
Enter
Return
The rating will automatically block certain categories that are more restrictive.
The rating titles (for example: Humor Level..etc) and TV ratings (for example: NV, MV,
V...etc) may differ depending on the broadcasting station.
The number of all rating title
English - 22
Upgrading the Software
Samsung may offer upgrades for your TV’s firmware in the future. Please contact the
Samsung call center at 1-800-SAMSUNG to receive information about downloading
upgrades and using a USB drive. Upgrades will be possible by connecting a USB drive to
the USB port located on the back of your TV.
USB Drive
1
2
Insert a USB drive containing the firmware upgrade into the USB Upgrade Port on the back of
the TV.
Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Setup, then press the ENTER button.
3
4
Press the ▲ or ▼ button to select Software upgrade, then press the ENTER button.
Software upgrade
Press the ▲ or ▼ button to select USB Upgrade, then press the ENTER button.
The message Scanning for USB... It may take up to 30 seconds. is displayed.
Please be careful to not disconnect the power or remove the USB drive while upgrades are
being applied.
USB Upgrade
►
The TV will shut off and turn on automatically after completing the firmware upgrade.
Please check the firmware version after the upgrades are complete.
The firmware and upgrade process may be different by country and region.
Move
Enter
Return
➢
USB Upgrade
Scanning for USB...
It may take up to 30 seconds.
Identifying Problems
If the TV seems to have a problem, first try this list of possible problems and solutions.
If none of these troubleshooting tips apply, call your nearest Samsung service center.
Problem
Possible Solution
Poor picture quality.
Try another channel.
Adjust the antenna.
Check all wire connections.
Poor sound quality.
No picture or sound.
Try another channel.
Adjust the antenna.
Try another channel.
Press the SOURCE button.
Make sure the TV is plugged in.
Check the antenna connections.
Make sure the MUTE button is off.
No sound or sound is too low at
maximum volume.
First, check the volume of units connected to your TV (digital broadcasting receiver, DVD,
cable broadcasting receiver, VCR, etc.). Then, adjust the TV volume accordingly.
Picture rolls vertically.
Check all connections.
The TV operates erratically.
The TV won’t turn on.
Unplug the TV for 30 seconds, then try operating it again.
Make sure the wall outlet is working.
Remote control malfunctions
Replace the remote control batteries.
Clean the upper edge of the remote control(transmission window).
Check the battery terminals.
Press the TV/DTV button to put your remote control in the “TV” mode.
Make sure the remote has batteries.
Check that the “+” and “-” ends of the batteries are inserted correctly.
Digital broadcasting screen problem. Please check the digital signal strength and input antenna.
The image is too light or too dark.
Adjust the Brightness and Contrast.
Adjust the Fine tuning.
The visual qualities of digital
channels vary.
The visual qualities of digital channels may vary depending on the original production
method(analog or digital).
-
-
If the original production method is digital: High visual quality program.
If the original production method is analog: The digital program displayed on the screen is
originally an analog program which has been converted to digital. The visual quality is of an
SD(Standard Definition) grade.
Although the TV caption shows HD,
the visual quality is not satisfactory.
The HD(High Definition) caption that appears when switching channels or when pressing the
Information button on the remote control means the selected channel is a digital channel. If the
broadcasting station converts an analog signal into digital and transmits the signal, the visual
quality may not be perfect.
English - 23
Specifications
Model Name
TX-T2781
TX-T2782
TX-T2082
Screen Size (Diagonal)
Sound Output
27 inches
20 inches
5W X 2
Dimensions (WxHxD)
Body
30.35 x 23.34x 16.53 inches /
771 x 593 x 420 mm
31.33 x 23.34 x 16.57 inches /
796 x 593 x 421 mm
23.77 x 18.58 x 14.19 inches /
604 x 472 x 360.5 mm
Weight
90.38 lbs / 41 Kg
94.79 lbs / 43 Kg
44.09 lbs / 20 Kg
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
50 °F to 104 °F (10 °C to 40 °C)
10% to 80%, non-condensing
-4 °F to 113 °F (-20 °C to 45 °C)
5% to 95%, non-condensing
Environmental
Considerations
Design and specifications are subject to change without prior notice.
For the power supply, refer to the label attached to the product.
➢
Contact SAMSUNG WORLD-WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
Country
Web Site
Address
Customer Care Center
Samsung Electronics Canada Inc., Customer Service
55 Standish Court Mississauga, Ontario L5R 4B2
Canada
CANADA
1-800-SAMSUNG (7267864)
Samsung Electronique Canada Inc., Service à la Clientèle
55 Standish Court Mississauga, Ontario L5R 4B2
Canada
Samsung Electronics America, Inc.
105 Challenger Road
U.S.A
1-800-SAMSUNG (7267864)
Ridgefield Park, NJ 07660-0511
AA68-03783D-01
|