1 x15″ Stackable
Aluminum Drive Bass Enclosure
Hartke
Connecting the 115XL
About Impedance
Before you hook up your speaker cabinet, be sure that you understand a little about
impedance. Impedance is the electronic load that the speaker puts on the power amplifier
and is measured in Ohms.
Here is the tricky, yet simple rule of impedance: When two speakers, of equal impedance
are wired in "Parallel", the total imped-
EFFECT
ance is cut in half and when two speak-
Hartke Systems
Distributed Exclusively by
Samson Technologies Corp.
Hicksville, New York 11802
RETUIRN
SEND
MODEL 2000
200 WATTS
~
AC INPUT
115V/230V 50/60Hz
FUSE
5A/250V, 180W (115V)
2.5A/250V, 450W (230V)
8
4
=
=
120 WATTS
200 WATTS
SPEAKER OUTPUTS
ers are wired in “Series,” the total
impedance is the sum of the speakers
individual impedance.
CAUTION
TO PREVENT SHOCK, DO NOT OPEN. NO USER SERVICE-
ABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL. TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE TO RAIN OR MOISTURE.
HPF
OFF
ON
8
8
SERIAL NUMBER
ASSEMBLED IN R.O.K.
The 115XL impedance is 8 Ohms.
So, when two 115XL’s are connected
together in parallel, the total impedance
is 4 Ohms. The impedance of your
speaker also has an effect on your
amplifier. In general, the lower the
impedance, the more power your ampli-
fier will put out.
Hartke
4.5XL BASS CABINET
400 WATTS
Hartke Systems Distributed worldwide by Samson echnologies
T
INPUTS
8
8
EXTENSION
MADE IN CHINA
SERIAL NUMBER
IMPORTANT: There is a minimum safe
impedance so be sure to check the
manufacturer’s recommended imped-
ance for your amplifier to avoid any
damage to your amplifier or voiding
your warranty.
EFFECT
Connecting the 115XL to Your Amplifier
The 115XL connections are made via
1/4” phone jacks located on the rear
panel jack-plate. Be sure to make your
connection with un-shielded speaker
cable. Connect the Amplifier Output to
the speaker Input on the 115XL’s rear
jackplate.
Hartke Systems
Distributed Exclusively by
Samson Technologies Corp.
Hicksville, New York 11802
RETUIRN
SEND
MODEL 2000
200 WATTS
~
AC INPUT
115V/230V 50/60Hz
FUSE
5A/250V, 180W (115V)
2.5A/250V, 450W (230V)
8
4
=
=
120 WATTS
200 WATTS
SPEAKER OUTPUTS
CAUTION
TO PREVENT SHOCK, DO NOT OPEN. NO USER SERVICE-
ABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL. TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE TO RAIN OR MOISTURE.
HPF
OFF
ON
8
8
SERIAL NUMBER
ASSEMBLED IN R.O.K.
Hartke
4.5XL BASS CABINET
400 WATTS
Hartke Systems Distributed worldwide by Samson echnologies
T
INPUTS
8
8
EXTENSION
MADE IN CHINA
SERIAL NUMBER
Using the EXTENSION Output
The 115XL provides a convenient
Extension Output for connecting addi-
tional speaker cabinets in parallel. Be
sure to read the section above on
impedance to insure a proper hook up
with your amplifier. Follow the steps
below to connect two 115XL ’s using
the Extension Output. Connect the
Amplifier Output to the Input of the first
115XL. Now, connect the Extension
Output to the Input of the second
115XL.
Hartke
4.5XL BASS CABINET
400 WATTS
Hartke Systems Distributed worldwide by Samson echnologies
T
INPUTS
Specifications
Hartke 115XL Specifications
Type
Tuned, Vented Enclosure
8 Ohms Impedance
200 Watts RMS Power Handling
1-Hartke 15XL8 Special Design
Aluminum 15", 8 ohm, 200 watt
drive unit
Impedance (Ohms)
Power Handling
Drivers
SPL
98dB
Frequency Response
Inputs
30Hz - 2.5kHz
Parallel 1/4”
Weight
63 lbs. (28.58)
Dimensions
Height:24" (60.96 cm)
Width: 24" (60.96 cm)
Depth: 15" (38.1 cm)
Hartke
Distributed Worldwide Exclusively by:
Samson Technologies Corp.
575 Underhill Blvd.
P.O. Box 9031
Syosset, NY 11791-9031
Phone: 1-800-3-SAMSON (1-800-372-6766)
Fax: 516-364-3888
|