OPERATOR’S MANUAL
AIRgrip™ LASER LEVEL
ELL0001
Your laser level has been engineered and manufactured to Ryobi’s high standards for depend-
ability, ease of operation, and operator safety. When properly cared for, it will give you years of
rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the
operator’s manual before using this product.
Thank you for buying a Ryobi product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
SAFETY RULES
n
Do not place the laser level in a position
that may cause anyone to stare into the
laser beam intentionally or unintention-
ally. Serious eye injury could result.
Do not operate the laser level around
children or allow children to operate the
tool. Serious eye injury could result.
Always turn the laser level off when not
in use. Leaving the tool on increases the
risk of someone inadvertently staring into
the laser beam.
WARNING!
READ AND UNDERSTAND ALL IN-
STRUCTIONS. Failure to follow all
instructions listed below, may result in
electric shock, fire and/or serious per-
sonal injury.
n
n
CAUTION:
n
n
Do not operate the laser level in com-
bustible areas such as in the presence
of flammable liquids, gasses or dust.
Do not use push pins unless you plan to
affix the base to a soft wood, wallboard,
or other easily penetrated surface. This
could result in injury because the pins are
very sharp instruments.
Use of controls or adjustments or perfor-
mance of procedures other than those
specified herein may result in hazardous
radiation exposure.
CAUTION:
The use of an optical instrument with this
product will increase eye hazard.
n
n
Always ensure the laser beam is aimed
at a surface without reflective proper-
ties. Shiny reflective materials are not
suitable for laser use.
When using the base, always check
to be sure the laser level is securely
seated. Damage to the tool and/or seri-
ous injury to the user could result if the
laser level falls.
All repairs should be made by an autho-
rized service representative or the laser
manufacturer.
Handle the laser level with care. Treat it
as you would any other optical device such
as a camera or binoculars.
The laser guide radiation used in this laser
level is Class IIIa with < 5mW and 635 nm
wavelengths. These lasers do not normally
present an optical hazard although staring at
the beam may cause flash blindness.
n
Avoid direct eye exposure when using
the laser and do not project the laser
beam directly into the eyes of others.
Serious eye injury could result.
Do not remove or deface any prod-
uct labels. Removing product labels
increases the risk of exposure to laser
radiation.
n
n
n
3
SAFETY RULES
n
Avoid exposing the laser level to shock, n Save these instructions. Refer to them
continuous vibration or extreme hot or
cold temperatures. Damage to the tool
and/or serious injury to the user could
result.
frequently and use them to instruct others
who may use this laser level. If you loan
someone this laser level, loan them these
instructions also.
4
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk as-
sociated with this product.
SYMBOL
SIGNAL
MEANING
DANGER:
Indicates an imminently hazardous situation,
which, if not avoided, will result in death or
serious injury.
WARNING:
Indicates a potentially hazardous situation,
which, if not avoided, could result in death or
serious injury.
CAUTION:
CAUTION:
Indicates a potentially hazardous situation,
which, if not avoided, may result in minor or
moderate injury.
(Without Safety Alert Symbol) Indicates a situ-
ation that may result in property damage.
SERVICE
WARNING:
This laser level has no serviceable parts. If the
unit fails due to normal wear and tear within
two years of purchase, return with original re-
ceipt for a replacement unit at no charge. Call
1-800-525-2579 for your nearest RYOBI
AUTHORIZED SERVICE CENTER.
To avoid serious personal injury, do not
attempt to use this product until you read
thoroughly and understand completely the
operator’s manual. Save this operator’s
manual and review frequently for con-
tinuing safe operation and instructing
others who may use this product.
SAVE THESE INSTRUCTIONS
5
FEATURES
PRODUCT SPECIFICATIONS
Recommended Use ......................................................................................................... Indoor
Length of Laser Line.............................................................. Up to 40 ft., Horizontal or Vertical
Laser ..................................................................................................Class IIIa, <5mW, 635 nm
Power Supply.........................................................................................2 AA, 1.5 Volt Batteries
Battery Life — Laser Only ..................................40 Hours Continuous Use—Alkaline Batteries
Battery Life — w/Vacuum..................................2.5 Hours Continuous Use—Alkaline Batteries
Operating Temperature ..........................................................................................32˚F to 104˚F
Dimensions.........................................................................................4-1/4 in. x 2-7/8 in. x 3 in.
Weight .................................................................................................... 8 oz. Without Batteries
Accuracy ..........................................± 1/2" at 20 ft. (Laser Lens Facing Battery Compartment)
± 3/4" at 15 ft. (Laser Lens 180° Opposed Battery Compartment)
LASER HEAD
LEVELS
ROUGH SURFACE
ADAPTOR
LASER
LENS
ON/OFF
SWITCH
Fig. 1
6
FEATURES
CASE
MULTI-FUNCTION BASE
VELCRO®
STRAP
PUSH
PINS
Fig. 2
KNOW YOUR LASER LEVEL
MULTI-FUNCTION BASE
See Figures 1 - 2.
The multi-function base allows your laser level
to be used on irregularly shaped walls or ob-
jects, as well as on a tripod. It features built-in
loops for a Velcro® strap, built-in angled holes
for push pins, and has a standard 1/4 in. - 20
tripod mounting hole. The base also protects
the laser level when using on a dusty or dirty
surface and during storage.
Before attempting to use this product, famil-
iarize yourself with all operating features and
safety rules.
AIRgrip™ VACUUM
TECHNOLOGY
Your laser level uses a vacuum base that can
adhere to smooth surfaces. Using the vacuum
seal prevents wall damage caused by nails,
pins or adhesive tape.
ON/OFF SWITCH
Your laser level conveniently turns on and off
at the touch of a switch.
CASE
ROUGH-SURFACE ADAPTOR
The rough-surface adaptor increases the
number of surfaces on which the AIRgrip™
vacuum can be used.
A padded and zippered case stores and pro-
tects your laser level when not in use.
LASER HEAD
The laser head on your level rotates 360˚.
VELCRO® STRAP/PUSH PINS
A Velcro® strap and push pins are provided
for attaching the laser level to a variety of
surfaces.
LASER LENS
Your level’s laser lens rotates 90˚ for wrapping
around inside corners and uneven surfaces.
7
ASSEMBLY
UNPACKING
WARNING:
This product has been shipped completely
assembled.
If any parts are missing, do not operate this
tool. Please return to the place of purchase
or call 1-800-525-2579 for assistance.
n
n
n
n
Carefully remove the tool and any accesso-
ries from the box. Make sure that all items
listed in the packing list are included.
Inspect the tool carefully to make sure
no breakage or damage occurred during
shipping.
WARNING:
Do not attempt to modify this tool or cre-
ate accessories not recommended for
use with this tool. Any such alteration or
modification is misuse and could result in
a hazardous condition leading to possible
serious personal injury.
Do not discard the packing material until
you have carefully inspected and satisfac-
torily operated the tool.
If any parts are damaged or missing, please
call 1-800-525-2579 for assistance.
PACKING LIST
Laser Level
Case
Velcro Strap
Push Pins (2)
Multi-function Base
Rough Surface Adaptor
AA Batteries (2)
Operator’s Manual
8
OPERATION
n
Place the battery cover plate back onto
the laser level and slide down to secure.
WARNING:
Do not allow familiarity with tools to
make you careless. Remember that
a careless fraction of a second is
sufficient to inflict serious injury.
BATTERY COVER PLATE
TO
REMOVE
APPLICATIONS
You may use this laser level for the following
purposes:
n
n
Hanging pictures
Hanging wallpaper and wallpaper bor-
ders
n
n
n
n
Lining up floor or wall tile
Lining up electrical outlets
Decorative angles for faux painting
Putting up chair rail
TO
INSTALL
BATTERIES
BATTERY
NOTE: This product is not a rotary laser. It
will need to be releveled for each direction it
is pointed to.
Fig. 3
COMPARTMENT
INSTALLING BATTERIES
See Figure 3.
WARNING:
The battery compartment is located beneath
the ridged area at the front of the laser level.
When turning on the laser level, always
protect the eyes of yourself and those
around you. Never point the laser beam
at anyone’s face, including your own.
To open:
n
Push the battery cover plate straight up
and remove.
n
Install two AA batteries according to
polarity indicators inside the battery
compartment.
NOTE: The horizontal and vertical vials are
to be used for reference only. This tool is not
intended to be a standard box beam level.
9
OPERATION
NOTE: The multi-function base is not used
when mounting by vacuum grip.
TURNING ON/OFF
See Figure 4.
n
Place the laser level on the surface you
want it secured to and push in slightly to
seal.
Press the switch located on the right side of
the laser level to turn it ON and OFF. Always
wait for at least 5 seconds between stopping
and restarting the laser level.
n
n
Continue to hold the laser level against the
surface while pressing the on/off switch.
Release the laser level when you hear a
change in motor sound.
NOTE: To release the vacuum seal, turn the
laser level’s power off. For fast release, press
the protrusion on the back of the unit. Pulling
the laser level off the wall without releasing the
vacuum could damage the tool.
PRESS TO
TURN ON
The laser will automatically shut off 15 min-
utes prior to battery failure, but the motor will
remain on. Press the on/off switch to power
down the unit and replace the batteries.
ON/OFF
SWITCH
PRESS TO
TURN OFF
Fig. 4
POSITIONING THE LASER LEVEL
The laser level has several positioning options
available to suit the needs of your project.
For a quick reference or alignment between
two points, the laser level can be hand held
or placed on a horizontal surface.
USING THE AIR-GRIP VACUUM
ON/OFF
SWITCH
See Figure 5.
Fig. 5
The laser level’s vacuum grip technology al-
lows attachment to most smooth surfaces.
10
OPERATION
n
Release the laser level when you hear a
change in motor sound.
ROUGH SURFACE ADAPTOR
See Figure 6.
Using the rough-surface adaptor, you can use
the laser level’s AIRgrip™ feature to positon the
unit on many non-smooth surfaces, including
brick and painted cinderblock.
NOTE: The AIRgrip™ feature cannot be used
with stucco or unpainted cinderblock.
USING MULTI-FUNCTION BASE
See Figure 7.
Velcro® strap, push pin, and tripod mounting
methods are available only when the multi-
function base is installed. To install the base:
n
While holding the laser level with the power
switch facing you, align the raised ridge on
the base with the groove on the level.
n
Position the rough-surface adaptor on the
surface where you want to secure the laser
level.
n
Slide the laser level and base completely
together.
NOTE: The dotted lines on the adaptor
should be visible.
NOTE: If the base is seated correctly, the
vacuum will not operate when the power
is turned on.
n
n
Place the laser level against the adaptor
on the dotted lines, and push in slightly to
engage the seal.
VELCRO® STRAP: The strap can be used
to attach the laser level to irregularly shaped
Continue to hold the laser level against the
surface while pressing the on/off switch.
Fig. 6
11
OPERATION
objects such as pipes, 2x4s, 2x6s, or metal n Align push pin with angled hole located on
grates.
one side of laser level base and push in to
secure.
n
Attach the strap to one side of the laser
level base by threading it through the loop n In the angled hole on the other side of laser
and fastening.
level base, secure the second push pin.
n
n
n
Position the laser level on the surface
where you want it mounted.
TRIPOD: The laser level base has a standard
1/4 in.-20 threaded fitting for attaching to a
tripod base (not included). This method of
mounting is ideal for leveling kitchen cabinets,
countertops, window framing, and more.
Wrap the strap around the object being
mounted (pipe, board, etc.).
Place the loose end of the strap through
the remaining loop on the laser level base
and secure.
CAUTION:
Use caution when using laser level in base.
Do not orient in a way that will allow the
laser level to slide or fall out of the base.
PUSH PINS: Push pins allow the laser level
to be mounted to stucco and permeable sur-
faces.
n
Place the laser level on the surface where
you want it mounted.
TRIPOD
HOLE
PUSH PINS
LOOP
PUSH
PIN HOLES
VELCRO®
STRAP
Fig. 7
12
OPERATION
ridge marks on the laser head with one of
ADJUSTING THE LASER LINE
the arrow marks on the body of the laser,
then rotate the laser head in the desired
direction until the next ridge is aligned with
the same arrow mark. Relevel the unit for
each wall, adjacent surface, or direction a
line is generated towards.
See Figure 8.
The laser level will project a straight line across
anobstructionorinterference, aswellasaround
inside corners and onto adjacent surfaces. The
line can be adjusted in two ways:
n
The line can be rotated 360˚ by turning
the laser head in a clockwise or coun-
terclockwise direction. To move the line
in 45° increments, align one of the raised
n
The line can also be rotated up to 90°, from
vertical to horizontal, by turning the lens
adjustment ring in a clockwise or counter-
clockwise direction.
RIDGE
MARKS
ARROW
MARK
Fig. 8
VERTICAL BEAM
HORIZONTAL BEAM
13
OPERATION
n
n
Turn on the laser.
OPERATING THE LASER LEVEL
See Figures 9 - 10.
Rotate the laser head to position the laser
line where needed.
n
Place the level in the area where you want
the laser line projected.
n
With the laser beam pointed away from
you, rotate the laser lens to achieve the
desired angle of beam.
n
If a true vertical line or level horizontal line
is desired, level the tool by centering the
bubbles inside the vials located on top of
the laser head.
NOTE: Due to construction inaccuracy, walls
may not be perfectly straight. This may cause
the laser to have slight variances when in the
level position.
NOTE: To ensure plumb lines or level hori-
zontal lines across adjacent surfaces, level
both vials and position the tool directly in
front of the work area.
TOP VIEW
CENTERED
LEVEL
Fig. 9
Fig. 10
14
MAINTENANCE
WARNING:
WARNING:
To avoid serious personal injury, always
remove the batteries from the tool when
cleaning or performing any maintenance.
Do not at any time let brake fluids, gaso-
line, petroleum-based products, penetrat-
ing oils, etc., come in contact with plastic
parts. Chemicals can damage, weaken or
destroy plastic which may result in serious
personal injury.
GENERAL MAINTENANCE
n
Before initial use, wipe AIRgrip™ vacuum
base with a damp cloth to remove any
residue.
n
n
To clean the laser lens, if needed, use
ONLY a soft cloth or cotton swab moist-
ened with glass cleaner.
n
n
Store the laser level indoors.
Check the batteries regularly to avoid de-
terioration. Remove the batteries from the
laser level if it is not going to be used for
an extended time.
When not in use, the laser level and base
should be kept in the protective case.
n
Keep the laser level free of dust and liquids.
Use a damp cloth and mild soap to clean
the outside casing. Avoid using solvents
when cleaning plastic parts. Most plastics
are susceptible to damage from various
types of commercial solvents and may be
damaged by their use.
n
n
Do not disassemble the laser level. This
could cause exposure to hazardous laser
radiation.
Do not attempt to change any part of the
laser lens.
ALWAYS BE AWARE of the loca-
tion where the laser light is emit-
ted when using the level. ALWAYS
MAKE SURE that any bystanders in
the vicinity of use are made aware
of the dangers of looking directly
into the laser beam.
15
TROUBLESHOOTING
PROBLEM
CAUSE
SOLUTION
Laser line projection is
weak.
Batteries are low.
Replace with fresh
batteries.
Laser is off, but motor is
on and vacuum is working.
Batteries are low.
Replace with fresh
batteries.
Laser line is hard to see.
Laser line is not level.
Light in area is too bright.
Use in dimmer area or use
laser-enhancing glasses.
1. Leveling bubbles not
properly aligned.
1. Make sure bubble on
vial is centered.
2. Level is mounted on
base that isn’t level.
2. Make sure the bubbles
are level after mounting
to base.
Laser line is horizontal
when a vertical line is
desired.
Laser lens is in the
incorrect position.
Turn the laser lens 90˚ to
the vertical orientation.
16
NOTES
17
OPERATOR’S MANUAL
AIRgrip™ LASER LEVEL
ELL0001
• SERVICE
This product has no serviceable parts. If unit fails due to normal wear and tear within two
years of purchase, return with original receipt for a replacement unit at no charge. Please
call 1-800-525-2579 for the nearest Ryobi Authorized Service Center. You can also check
• MODEL NO.
The model number of this tool will be found on a label attached to the top of the laser
level.
• HOW TO ORDER REPLACEMENT PARTS
When ordering replacement parts, always give the following information:
ELL0001
•
MODEL NUMBER
RYOBI TECHNOLOGIES, INC.
1428 Pearman Dairy Road, Anderson, SC 29625
Post Office Box 1207, Anderson, SC 29622-1207
Phone 1-800-525-2579
983000-559
10-04
|