NQPSMTR®
)ꢀꢁꢂ
• Layering Orchestral Sounds with the Organ Part
••• ROLAND VK-7 TURBO FACTS •••
The VK-7 is a totally new combo organ that utilizes Roland’s new
Virtual ToneWheel modeling technology to simulate the principles
behind tonewheel sound generation used in classic organs. Here
are just a few of the features that make the VK-7 a modern day
equivalent of the Hammond B3 :
The VK-7 contains 39 orchestral sounds that can be used as solo
instruments or layered with the organ sounds to provide more
depth, attack, bass, etc. Use the following procedure to layer an
orchestral sound with an organ sound:
1) Select the desired organ sound (as previously described).
2) Press MAIN (under ORCHESTRAL ASSIGN) so it is lit.
3) Press the desired ORCHESTRAL VOICES sound group
button.
4) Use the VARIATION UP/DOWN buttons to select the desired
instrument within that sound group.
5) Use the ORCHESTRAL LEVEL knob to adjust the volume as
desired.
•
Full keyboard polyphony with 91 voices in constant,
independent oscillation
•
High speed sound generation, allowing the VK-7 to respond to
the rigorous demands of classic organ playing styles
9 Harmonic bars for realtime manipulation of organ sounds
Sophisticated rotary speaker and tube amp simulation based
on Roland’s COSM technology
•
•
•
•
39 orchestral voices built-in
11-pin Rotary Tone Cabinet connector for use with Leslie
speaker cabinet
Real wood finish and portable cabinet design
2 MIDI IN connectors allow for a dual manual configuration
with pedals
MIDI information, including harmonic bar messages, is sent
and received in realtime
• Splitting the Keyboard
Use the following procedure to assign a bass sound to the lower
half of the keyboard and then set the split point:
1) Select the desired organ sound (as previously described).
2) Press SUB (under ORCHESTRAL ASSIGN) so it is lit.
3) Press SPLIT [SUB/MAIN].
4) Press the ORCHESTRAL VOICES [BASS] button.
5) Use the VARIATION UP/DOWN buttons to select the desired
bass sound.
•
•
•
• Initializing
6) Press the ORCHESTRAL VOICES [BASS] button again.
7) Press [ORGAN MUTE] to mute the organ sound.
Use the following procedure to restore the factory settings:
1) Press EDIT.
2) Press UTILITY [7].
3) Press the RIGHT CURSOR [>] button until “E7: Factory Setup”
is displayed.
4) Press the [+] button.
5) Press EXIT to return to the previous display.
Use the following procedure to set the split point:
1) Press EDIT followed by USER COMMON [3].
2) Use the [<]/[>] buttons to access the “Split Point” display.
3) Use the [+]/[-] buttons to set the split point as desired.
4) Press EXIT to return to the previous display.
• Playing the Demos
• Using a Dual Keyboard Configuration
Use the following procedure the play the VK-7 demo songs:
1) Press EDIT.
2) Press DEMO [8].
The VK-7 allows you to emulate a complete Hammond B3 setup
by simply adding an additional MIDI keyboard and a MIDI foot
controller (such as the Roland PK-5). Use the following procedure
to connect a MIDI keyboard and foot controller to the VK-7 in a dual
manual configuration(set the Sub keyboard to transmit on MIDI
channel 3 and the foot controller to channel 2):
1) Connect the MIDI OUT on the additional MIDI keyboard (Sub
keyboard) to the KEYBOARD IN on the VK-7.
2) Set the MIDI Select switch (on the rear panel) to the “SUB
KEYBOARD” position.
3) Connect the MIDI OUT of the MIDI foot controller to the PEDAL
IN on the VK-7.
3) Use the [<]/[>] buttons to select “SinglePlay.”
NOTE: To hear consecutive playback of all demo
songs, select “Chain Play.”
4) Use the [+]/[-] buttons to select the desired song.
5) Press WRITE to start playback.
6) Press EXIT to stop playback.
7) Press EXIT again to return to the previous display.
• Selecting Sounds
4) Set the MIDI transmit channel on the Sub keyboard to 3 and
the foot controller to 2.
5) Play the Sub keyboard to hear the Sub Part and play the foot
controller to hear the Pedal Part on the VK-7 (make sure that
the VK-7’s audio outputs are connected).
6) Press MAIN (under HARMONIC BAR PART).
7) Play the VK-7’s keyboard and adjust the Harmonic Bars as
desired. The changes will be reflected in the sound of the Main
Part.
8) Press SUB (under HARMONIC BAR PART).
9) Play the Sub keyboard and adjust the Harmonic Bars on the
VK-7 as desired. The changes will be reflected in the sound of
the Sub Part.
The VK-7 has 64 different organ sounds. These sounds are
organized into eight groups (banks) with eight sounds in each
group. There are two modes of operation for the banks. In
“Alternate” mode (the default setting) the BANK button is used to
quickly switch between the first two banks. “Expand” mode is used
to gain access to all eight banks. Use the following procedure to
enable “Expand” mode and select sounds:
1) Press EDIT (the [1]-[8] buttons will start to flash).
2) Press SYSTEM BASIC [1].
3) Use the [<]/[>] buttons to access the “E1: Bank Function”
display and press the [+] button to select “Expand.”
4) Press EXIT.
5) Press BANK (the [1]-[8] buttons will start to flash). Use the [1]-
[8] buttons to select a bank.
NOTE: If you are using a PK-5 MIDI Foot Controller, you will
probably want to transpose it up one octave from its default
settings.
6) Use the [1]-[8] buttons to select a sound from that bank.
* All trademarks are property of their respective owners.
TBS60
© 1997 RolDaonwdnlCoaodrfproomraWtiwown.SUom.Sa.n,u7al2s.0co0mD. Aolml MianniouanlsCSieracrlceh,ALnodsDoAwnngloeadle. s, CA 90040
5/97
|