M3T-F160-128NRD
Converter Board for Connecting FLX160 to 128-pin 0.5-mm-pitch LQFP
User's Manual
Keep safety first in your circuit designs!
• Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products better and more
reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property
damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive,
auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap.
Notes regarding these materials
• These materials are intended as a reference to assist our customers in the selection of the Renesas Technology product best suited to the customer's
application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corporation,
Renesas Solutions Corporation or a third party.
• Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage, or infringement of any third-party's rights,
originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials.
• All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the
time of publication of these materials, and are subject to change by Renesas Technology Corporation and Renesas Solutions Corporation without notice
due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corporation, Renesas Solutions
Corporation or an authorized Renesas Technology product distributor for the latest product information before purchasing a product listed herein. The
information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corporation and Renesas Solutions
Corporation assume no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information
published by Renesas Technology Corporation and Renesas Solutions Corporation by various means, including the Renesas home page (http://
www.renesas.com).
• When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure
to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology
Corporation and Renesas Solutions Corporation assume no responsibility for any damage, liability or other loss resulting from the information contained herein.
• Renesas Technology semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human
life is potentially at stake. Please contact Renesas Technology Corporation, Renesas Solutions Corporation or an authorized Renesas Technology product
distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular,
medical, aerospace, nuclear, or undersea repeater use.
• The prior written approval of Renesas Technology Corporation and Renesas Solutions Corporation is necessary to reprint or reproduce in whole or in part
these materials.
• If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese
government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and
regulations of Japan and/or the country of destination is prohibited.
• Please contact Renesas Technology Corporation or Renesas Solutions Corporation for further details on these materials or the products contained therein.
Precautions to be taken when using this product
• This product is a development supporting unit for use in your program development and evaluation stages. In mass-producing your program you have
finished developing, be sure to make a judgment on your own risk that it can be put to practical use by performing integration test, evaluation, or some
experiment else.
• In no event shall Renesas Solutions Corporation be liable for any consequence arising from the use of this product.
• Renesas Solutions Corporation strives to renovate or provide a workaround for product malfunction at some charge or without charge. However, this does
not necessarily mean that Renesas Solutions Corporation guarantees the renovation or the provision under any circumstances.
• This product has been developed by assuming its use for program development and evaluation in laboratories. Therefore, it does not fall under the
application of Electrical Appliance and Material Safety Law and protection against electromagnetic interference when used in Japan.
If the requirements shown in the "CAUTION" sentences are ignored,
the equipment may cause personal injury or damage to the products.
CAUTION
Rev. 1.00
July 1, 2003
REJ10J0233-0100Z
5. Connection Procedure (See Figure 3)
The procedure for connecting the M3T-F160-128NRD is
shown below.
(1) Mount the NQPACK128RD on the target system.
(2) Attach the YQPACK128RD on the NQPACK128RD.
FLX160-PRB
or
M3xxxxTx-EPB
(3) Secure the four corners of the YQPACK128RD with the
YQ-GUIDE's.
• Do NOT use the screws included with the
YQPACK128RD.
M3T-F160-128NRD
• Do NOT use the screwdriver included with the
NQPACK128RD that is used only for the
HQPACK128RD.
Use a slotted screwdriver.
(4) Attach the probe of the emulation pod to the M3T-F160-
128NRD.
YQ-GUIDE's (x4)
YQPACK128RD
(5) Attach the M3T-F160-128NRD on the YQPACK128RD.
NQPACK128RD
128-pin 0.5-mm-pitch
(128P6Q-A) foot pattern
: Position of No. 1 pin
Be sure to align the pins.
Figure 3 Connection procedure
6. External Dimensions and a Sample Foot Pattern
Unit: mm
Figure 4 External dimensions and a sample foot pattern
( 3 / 4 )
7. Precautions
CAUTION
Cautions to Be Taken for This Product:
• To connect the YQPACK128RD, be sure to use the included YQ-GUIDE's.
• Do NOT use the screws included with the YQPACK128RD in order to connect the
YQPACK128RD.
IMPORTANT
Notes on This Product:
• We cannot accept any request for repair.
• For purchasing the NQPACK128RD, YQPACK128RD, HQPACK128RD, contact
the following:
• For inquiries about the product or the contents of this manual, contact your local
distributor.
8. Correspondence of the Connectors CN1 and CN2
Table 2 Correspondence of the connectors
CN1
1a
IC1
-
CN1
1b
IC1
16
14
12
-
CN2
1a
IC1
-
CN2
1b
IC1
17
19
21
23
25
27
29
31
33
-
35
37
39
41
43
45
47
49
51
-
2a
15
13
11
-
2b
2a
18
20
22
24
26
28
30
32
34
-
36
38
40
42
44
46
48
50
52
-
54
55
56
58
60
62
64
66
68
-
2b
3a
3b
3a
3b
4a
4b
4a
4b
5a
5b
-
5a
5b
6a
-
6b
-
6a
6b
7a
10
8
7b
9
7a
7b
8a
8b
7
8a
8b
9a
6
9b
5
9a
9b
10a
11a
12a
13a
14a
15a
16a
17a
18a
19a
20a
21a
22a
23a
24a
25a
26a
27a
28a
29a
30a
31a
32a
33a
34a
35a
36a
37a
38a
39a
40a
4
10b
11b
12b
13b
14b
15b
16b
17b
18b
19b
20b
21b
22b
23b
24b
25b
26b
27b
28b
29b
30b
31b
32b
33b
34b
35b
36b
37b
38b
39b
40b
-
10a
11a
12a
13a
14a
15a
16a
17a
18a
19a
20a
21a
22a
23a
24a
25a
26a
27a
28a
29a
30a
31a
32a
33a
34a
35a
36a
37a
38a
39a
40a
10b
11b
12b
13b
14b
15b
16b
17b
18b
19b
20b
21b
22b
23b
24b
25b
26b
27b
28b
29b
30b
31b
32b
33b
34b
35b
36b
37b
38b
39b
40b
-
3
2
1
128
126
124
122
120
119
118
116
-
127
125
123
121
-
-
117
-
115
113
111
109
-
-
-
106
104
-
102
100
98
96
94
92
90
88
86
-
53
-
-
114
112
110
108
-
57
59
61
63
65
67
-
69
70
71
73
75
77
79
81
83
-
-
107
105
103
-
101
99
97
95
93
91
89
87
85
-
-
72
74
76
78
80
82
84
("-": No connection)
( 4 / 4 )
|