M34553T-PTCB
Converter Board for 48-pin 0.5-mm-pitch LQFP (4553 Group)
User’s Manual
Keep safety first in your circuit designs!
z Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products
better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to
personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with
appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention
against any malfunction or mishap.
Notes regarding these materials
z These materials are intended as a reference to assist our customers in the selection of the Renesas Technology product best suited
to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to
Renesas Technology Corporation, Renesas Solutions Corporation or a third party.
z Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any damage, or infringement of
any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application
examples contained in these materials.
z All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information
on products at the time of publication of these materials, and are subject to change by Renesas Technology Corporation and
Renesas Solutions Corporation without notice due to product improvements or other reasons. It is therefore recommended that
customers contact Renesas Technology Corporation, Renesas Solutions Corporation or an authorized Renesas Technology product
distributor for the latest product information before purchasing a product listed herein. The information described here may contain
technical inaccuracies or typographical errors. Renesas Technology Corporation and Renesas Solutions Corporation assume no
responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information
published by Renesas Technology Corporation and Renesas Solutions Corporation by various means, including the Renesas home
page (http://www.renesas.com).
z When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and
algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the
information and products. Renesas Technology Corporation and Renesas Solutions Corporation assume no responsibility for any
damage, liability or other loss resulting from the information contained herein.
z Renesas Technology semiconductors are not designed or manufactured for use in a device or system that is used under
circumstances in which human life is potentially at stake. Please contact Renesas Technology Corporation, Renesas Solutions
Corporation or an authorized Renesas Technology product distributor when considering the use of a product contained herein for any
specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use.
z The prior written approval of Renesas Technology Corporation and Renesas Solutions Corporation is necessary to reprint or
reproduce in whole or in part these materials.
z If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from
the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport
contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
z Please contact Renesas Technology Corporation or Renesas Solutions Corporation for further details on these materials or the
products contained therein.
Precautions to be taken when using this product
z This product is a development supporting unit for use in your program development and evaluation stages. In mass-producing your
program you have finished developing, be sure to make a judgment on your own risk that it can be put to practical use by performing
integration test, evaluation, or some experiment else.
z In no event shall Renesas Solutions Corporation be liable for any consequence arising from the use of this product.
z Renesas Solutions Corporation strives to renovate or provide a workaround for product malfunction at some charge or without charge.
However, this does not necessarily mean that Renesas Solutions Corporation guarantees the renovation or the provision under any
circumstances.
z This product has been developed by assuming its use for program development and evaluation in laboratories. Therefore, it does not
fall under the application of Electrical Appliance and Material Safety Law and protection against electromagnetic interference when
used in Japan.
If the requirements shown in the "CAUTION" sentences are ignored,
the equipment may cause personal injury or damage to the products.
CAUTION
Rev.1.00
(1/4)
03.09.01
REJ10J0132-0100Z
5. Connection Procedure (See Figure 3)
3. Mount the NQPACK048SD.
4. Attach the YQPACK048SD on the NQPACK048SD.
5. Secure the four corners of the YQPACK048SD with the
YQ-GUIDE's.
M34553T-PTCA
(5)
M34553T-PTCB
z Do NOT use the screws included with the
YQPACK048SD for securing it.
z Do NOT use the driver included with the
NQPACK048SD for securing the YQ-GUIDE’s. It is
used for securing the HQPACK048SD.
(4)
Use a flat blade driver.
(3)
YQ-GUIDE’s (x4)
YQPACK048SD
These corners are not round.
6. Attach the M34553T-PTCB to the YQPACK048SD.
7. Connect the M34553T-PTCA converter board to the
M34553T-PTCB.
(2)
NQPACK048SD
(1)
Before using the M34553T-PTCB, be sure to read "7.
Precautions" on page 4.
48-pin 0.5-mm-pitch
(48P6Q-A) foot pattern
Target system
: No. 1 pin position
Be sure to align the pin.
Figure 3 Connection procedure of the M34553T-PTCB
6. External Dimensions and a Sample Foot Pattern (see Figure 4)
35
25
36
RENESAS
M34553T-PTCB REV.A
10
35
0.5
6.5
MADE IN JAPAN
1
12
0.5
0.25
28
Unit: mm
Figure 4 External dimensions and a sample foot pattern
(3/4)
7. Precautions
CAUTION
Cautions to Be Taken for Handling This Product:
● Be sure to align the pins when connecting the M34553T-PTCB.
● Do not apply excessive stress to the M34553T-PTCB main unit.
● To attach the M34553T-PTCB, be sure to use the YQ-GUIDE’s included with this product.
● Do not use the screws included with the YQPACK048SD for securing it.
IMPORTANT
Regarding This Product:
● We cannot accept any request for repair.
● For purchasing the NQPACK048SD, YQPACK048SD and HQPACK048SD, contact the following:
Tokyo Eletech Corporation
● For inquiries about this product or the contents of this manual, contact your local distributor.
8. Correspondence of Connectors J1, J2
Table 2 lists the correspondence of the M34553T-PTCB and NQPACK.
Table 2 Correspondence of the M34553T-PTCB and NQPACK
Pin number of
connector J1
Pin number of
connector J1
NQPACK
Signal
NQPACK
Signal
1
2
3
4
5
6
7
8
41
42
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
NC
SEG12
SEG13
XIN
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
NC
45
46
47
48
1
2
3
4
5
NC
D5/INT
P20/SEG17
P21/SEG18
P22/SEG19
P23/SEG20
P00/SEG21
P01/SEG22
P02/SEG23
P03/SEG24
P10/SEG25
P11/SEG26
P12/SEG27
P13/SEG28
D0
XOUT
CNVSS
XCIN/D6
XCOUT/D7
RESET*
COM0
COM1
COM2
COM3
SEG0/VLC3
SEG1/VLC2
SEG2/VLC1
SEG3
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
6
7
8
9
10
11
12
13
14
15
16
17
18
43
44
D1
D2
D3
D4
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
SEG10
SEG11
NC
D5/INT
C/CNTR
VDD
VSS
SEG14
SEG15
(NC: No connection)
(4/4)
|