RCA Telephone 25415 User Guide

4-Line Intercom Speakerphone

with Answerer and Caller ID

User’s Guide

Please read this manual

before operating product

for the ﬁrst time.

Model 25415

Important Information

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be

installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be

co-located or operated in conjunction with any other antenna or transmitter.”

For body worn operation, this phone has been tested and meets the FCC RF exposure guidelines when used with the belt clip supplied

with this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines.

Licensing

Licensed under US Patent 6,427,009.

Hearing Aid Compatibility

This telephone system meets FCC standards for Hearing Aid Compatibility.

US Number is located on the cabinet bottom

REN number is located on the cabinet bottom

CAUTION: When using telephone equipment, there are basic safety instructions that should always be followed. Refer to the IMPORTANT SAFETY

INSTRUCTIONS provided with this product and save them for future reference.

Your Four-Line Speakerphone is a full-featured phone ideally suited for home-ofﬁce use. It is designed to receive calls on up to four

incoming telephone lines and to serve up to 16 station users. Your phone features 16 memory locations, 94 phone book memories, hold,

conference call, intercom, call transfer, Caller ID display, and speakerphone capabilities. It also features an Auto Attendant function, which

will pick up and redirect incoming calls to other extensions in the system per the caller’s input. It is possible to enhance your phone to a

cordless feature with the additional purchase of the H5400 accessory handset and module.

This telephone is designed to be simple to use, however, you can reach its full potential more quickly by taking a few minutes to read this

user’s guide.

IMPORTANT: In order to use all of the Caller ID features of this telephone, you must subscribe to two separate services available from your local telephone

company: the standard Name/Number Caller ID Service to know who is calling when the phone rings and Call Waiting Caller ID Service to know who is calling while

you are on the phone

CAUTION:

RISKOFELECTRICSHOCK

DONOTOPEN

THE EXCLAMATION

POINT WITHIN THE

TRIANGLE IS A

THE LIGHTNING

CAUTION: TO REDUCE THE

FLASH AND ARROW RISK OF ELECTRIC SHOCK, DO

HEAD WITHIN THE NOT REMOVE COVER (OR

WARNING:TO

WARNING SIGN

ALERTING YOU OF

IMPORTANT

BACK). NO USER

PREVENT FIRE OR

ELECTRICAL SHOCK

HAZARD, DO NOT

EXPOSETHIS

TRIANGLE IS A

WARNING SIGN

ALERTING YOU OF

“DANGEROUS

VOLTAGE” INSIDE

THE PRODUCT.

SERVICEABLE PARTS INSIDE.

REFER SERVICING TO

QUALIFIED SERVICE

PERSONNEL.

INSTRUCTIONS

ACCOMPANYING

THE PRODUCT.

PRODUCT TO RAIN

OR MOISTURE.

SEE MARKING ON BOTTOM / BACK OF PRODUCT

Table of Contents

Providing Privacy...................................................................................................18

VOLUME ...............................................................................................................18

Ringer Volume ........................................................................................................18

Speakerphone, Handset, and Headset Volume.............................................18

CONFERENCE CALLS ..............................................................................................18

INTERCOM CALLS .................................................................................... 19

ONE-TOUCH INTERCOM.........................................................................................19

ANSWERING AN INTERCOM CALL............................................................................19

INTERCOM HOLD...................................................................................................19

INTERCOM CONFERENCE CALLS ..............................................................................19

PAGING ALL STATIONS ..........................................................................................20

CALLER ID............................................................................................. 20

SUMMARY SCREEN................................................................................................20

RECEIVING AND STORING CID RECORDS................................................................20

Reviewing CID Records ........................................................................................20

Saving CID Record to Intercom/Memory Log or Phone Book Memory20

Deleting a CID Record..........................................................................................20

Deleting All Call Records.....................................................................................20

Dialing Back.............................................................................................................21

IF YOU PROGRAMMED YOUR LOCAL AREA CODE....................................................21

IF YOU DID NOT PROGRAM YOUR LOCAL AREA CODE ...........................................21

CALL WAITING CALLER ID....................................................................................21

MEMORY LOG AND PHONE BOOK (DIRECTORY) MEMORY.......................................21

Storing a Number and Name in Memory.......................................................21

Reviewing Phone Book (Directory) Memory.................................................22

Reviewing the Intercom/Memory Log ...........................................................22

Editing a Name or Number Stored in Phone Book Memory....................22

Editing a Name or Number Stored in the Intercom/Memory Log ........22

Storing the Last Number Dialed .......................................................................22

Storing a Pause in Memory ................................................................................22

Dialing a Stored Number.....................................................................................22

Memory Delete/Clear............................................................................................22

Clear All Memories................................................................................................23

Chain Dialing...........................................................................................................23

ANSWERING SYSTEM ................................................................................ 23

ANSWERING MACHINE..........................................................................................23

TURNING THE ANSWERING SYSTEM ON/OFF...........................................................23

RECORDING A GREETING........................................................................................23

PLAYBACK AND ERASING A GREETING.....................................................................23

RECORDING INCOMING MESSAGES.........................................................................24

MONITORING INCOMING CALLS..............................................................................24

MEMO RECORDING...............................................................................................24

TWO-WAY RECORDING.........................................................................................24

MESSAGE PLAYBACK .............................................................................................24

DELETING MESSAGES ............................................................................................24

A^{CCESSING THE}ANSWERING SYSTEM FROM ANOTHER LOCATION.............................25

CONNECTING WITH THE ANSWERING SYSTEM..........................................................25

TOLL SAVER OPERATION ........................................................................................25

AUTO ATTENDANT.................................................................................... 25

TURN AUTO ATTENDANT ON/OFF ..........................................................................25

AUTO ATTENDANT SEQUENCE FOR CALLERS.............................................................25

RECORDING AUTO ATTENDANT GREETINGS..............................................................26

PLAYBACK AND ERASING AUTO ATTENDANT GREETINGS...........................................26

USING MULTIPLE AUTO ATTENDANTS .....................................................................26

DISPLAY MESSAGES ................................................................................. 27

OPERATION BY BATTERY............................................................................ 27

OPERATION WITHOUT POWER...................................................................... 27

CORDLESS PHONE OPTION ......................................................................... 27

TROUBLESHOOTING GUIDE .......................................................................... 27

GENERAL PRODUCT CARE .......................................................................... 28

SERVICE ................................................................................................. 28

ACCESSORY INFORMATION.......................................................................... 28

LIMITED WARRANTY ................................................................................. 29

EQUIPMENT APPROVAL INFORMATION..............................................................2

INTERFERENCE INFORMATION..........................................................................2

FCC RF RADIATION EXPOSURE STATEMENT.....................................................3

LICENSING .................................................................................................3

HEARING AID COMPATIBILITY ........................................................................3

PARTS CHECKLIST........................................................................................5

TELEPHONE JACK REQUIREMENTS....................................................................5

BASE LAYOUT ............................................................................................5

IMPORTANT INSTALLATION INFORMATION ..........................................................6

IMPORTANT INSTALLATION GUIDELINES.............................................................6

INSTALLING THE PHONE................................................................................6

DATA PORT ...............................................................................................8

SYSTEM VERIFICATION..................................................................................8

OTHER SYSTEM PHONES...............................................................................8

PROGRAMMING THE TELEPHONE .....................................................................8

LANGUAGE..............................................................................................................8

RINGER TONE .........................................................................................................8

PRIORITY LINE.........................................................................................................9

DELAY RING ...........................................................................................................9

PHONE ID..............................................................................................................9

PHONE NAME.........................................................................................................9

INTERCOM AUTO ANSWER .....................................................................................10

FLASH TIME..........................................................................................................10

CALL ALERT TONE.................................................................................................10

NO UNKNOWN/BLOCKED ......................................................................................10

DISPLAY CONTRAST ...............................................................................................11

LOCAL AREA CODE................................................................................................11

REGIONAL AREA CODES ........................................................................................11

MANUALLY SETTING THE TIME AND DATE...............................................................11

HOUR FORMAT .....................................................................................................12

RESTORING THE DEFAULT SETTINGS ........................................................................12

PROGRAMMING THE ANSWERING MACHINE................................................... 12

PICKUP DELAY ......................................................................................................12

MESSAGE LENGTH.................................................................................................13

CALL SCREENING ..................................................................................................13

MESSAGE INTERRUPT.............................................................................................13

REMOTE PASSWORD..............................................................................................13

MAILBOX..............................................................................................................14

PROGRAMMING THE AUTO ATTENDANT......................................................... 14

AUTO ATTENDANT PICKUP DELAY...........................................................................14

SET DAY TIME FOR AUTO ATTENDANT....................................................................14

SET NIGHT TIME FOR AUTO ATTENDANT.................................................................15

SET NIGHT TIME ON / OFF.................................................................................15

SET WEEKEND GREETING ......................................................................................15

SET VALID ID.......................................................................................................15

BASIC OPERATION.................................................................................... 16

MAKING CALLS WITH THE HANDSET.......................................................................16

MAKING CALLS WITH THE SPEAKERPHONE ..............................................................16

MAKING CALLS WITH THE OPTIONAL HEADSET........................................................16

PRE-DIALING.........................................................................................................16

ANSWERING CALLS ...............................................................................................16

SWITCHING BETWEEN THE SPEAKERPHONE, HANDSET, AND HEADSET .......................17

MUTE...................................................................................................................17

DO NOT DISTURB .................................................................................................17

HOLD ...................................................................................................................17

Placing a Call on Hold..........................................................................................17

Releasing a Call from Hold .................................................................................17

FLASH ..................................................................................................................17

REDIAL .................................................................................................................17

REVIEWING THE REDIAL NUMBERS .........................................................................17

TRANSFERRING A CALL TO ANOTHER STATION .........................................................18

RECEIVING A TRANSFERRED CALL FROM ANOTHER STATION .....................................18

PRIVACY ...............................................................................................................18

Connections & Setup

Parts Checklist

Make sure your package includes the following items:

INTERCOM/MEMORY LOG

INT.

ATTENDANT

DIRECTORY

(button)

MEM.

MEMO

(button)

EXIT

(button)

INT.

MEM.

STORE

(button)

ANSWERER

MEMO

STORE

INT.

MEM.

INT.

MEM.

DIAL

(button)

headset jack

INT.

DELETE

(button)

PRIVACY

(button)

MEM.

INT.

DELETE

EXIT

PLAY/STOP

REVIEW

SELECT/SAVE

DIAL

MEM.

INTERCOM

(button)

INT.

MEM.

PRIVACY

PAGE

INTERCOM

CONFER

INT.

MEM.

PAGE

(button)

INT.

CONFER

(button)

LINE 4

(button)

ABC

DEF

MEM.

INT.

TRANSFER

LINE

MEM.

TRANSFER

(button)

GHI

JKL

TUV

MNO

INT.

REDIAL

FORMAT

MEM.

INT.

LINE 3

(button)

PQRS

WXYZ

MEM.

INT.

MEM.

INT.

REDIAL/FORMAT

(button)

LINE 2

(button)

VOLUME

FLASH

OPER

PAUSE

TONE

MEM.

INT.

LINE 1

(button)

MEM.

HEADSET

SPEAKER

MUTE

HOLD

INT.

MEM.

VOLUME

(buttons)

MUTE

(button)

HOLD

FLASH

(button)

HEADSET

(button)

SPEAKER

(button)

#PAUSE

(button)

microphone

(for speakerphone)

Connections & Setup

Important Installation Information

•

Never install telephone wiring during a lightning storm.

Never install telephone jacks in wet locations unless the jack is speciﬁcally designed for wet locations.

Never touch non-insulated telephone wires or terminals, unless the telephone line is disconnected from the network.

Use caution when installing or modifying telephone lines.

Temporarily disconnect any equipment connected to the phone such as faxes, other phones, or modems.

Important Installation Guidelines

•

Install telephone near both a telephone (modular) jack and an electrical power outlet.

•

Avoid sources of noise, such as a window by a busy street, and electrical noise, such as motors, microwave ovens,

and ﬂuorescent lighting.

•

Avoid heat sources, such as heating air ducts, heating appliances, radiators, and direct sunlight.

Avoid areas of excessive moisture or extremely low temperature.

Avoid dusty locations.

Avoid other cordless telephones or personal computers.

CAUTION: Always disconnect all phone cords from the base unit before battery installation or replacement.

Installing the Phone

The phone may be connected to two 2-line (RJ14C) wall jacks or four single line (RJ11C) wall jacks to

accomodate all four lines.

1. Choose an area near an electrical outlet and telephone wall jack. Your phone should be placed on a

level surface, such as a table top or desk.

2. Install 4 AAA-size alkaline batteries (not included) for back up power in the event of a power failure.

• Use a screwdriver to loosen and lift up the battery compartment door located on the bottom

of the phone.

• Insert the batteries as shown on the diagram inside the battery compartment.

• Snap the battery compartment door back into place and tighten the screw.

NOTE: If the low battery icon appears in the display, you need to replace the batteries. It is important that you replace them as

soon as possible to maintain unit operation when electrical power is off. As a precaution, you may want to write down any stored

information you do not want erased.

IMPORTANT: If you are not going to use the telephone for more than 30 days, remove the batteries because they can leak and

damage the unit.

3. Plug the power supply cord into the power jack on the back of the base and the other end into an electrical outlet.

CAUTION: Use only the ATLINKS USA 5-2651 power adaptor that is compatible with this unit. Using other power adaptors may damage the unit.

Connections & Setup

4. Connect the telephone line cords:

If you have two dual line wall jacks installed in your home or ofﬁce, plug one end of the straight telephone line cord tagged as “LINE

1+2” into the jack marked LINE 1 + 2 and one end of the other straight line cord into the other jack on the back of the base. Plug the

other end of each line cord into the dual-line wall jacks.

LINE

1 + 2

LINE

3 + 4

If you have four single-line wall jacks installed in your home or ofﬁce, you must use adaptors/couplers (not included) to combine the

four single telephone lines into two dual lines. The adaptor/coupler may look similar to the one pictured here and can be purchased

from your local telephone products retailer.

Adaptor/coupler

LINE 1 + 2

Adaptor/coupler

LINE 3 + 4

NOTE: To use four lines, you must have four telephone lines with unique telephone numbers. If you only have one telephone line, this phone will still operate, but

only as a single line telephone.

Unit Initialization:

After you connect the power supply and Line 1 to the unit, the system automatically searches for and sets up a phone ID. To set your

own Phone ID, or change your phone ID, follow the steps in the Phone ID section.

You may connect up to 16 RCA 25413, 25414 and/or 25415 phones to the system at one time. Features like intercom, page and call

transfer may be used among the units, but Line 1 must be common for all 25413, 25414, or 25415 units for these features to work

properly. You may choose to share or privatize lines 2, 3 and 4.

5. Connect the handset cord:

Connect one end of the coiled handset cord to the jack on the side of the base and the other end into the jack in the handset, and place

the handset in the cradle.

6. Check for a dial tone:

Lift the handset and listen for a dial tone. If you hear a dial tone, the phone is properly installed.

Programming the Telephone

Data Port

This phone has a data port jack to connect an auxiliary phone device, such as a fax machine, computer modem, answering machine, or even

a cordless phone.

The data port switch on the back of the phone controls the data port jack so you can choose line 1, line 2, line 3, or line 4.

Use the data port to hook up your fax machine, for example, and then set the data port switch to line 4 in order to receive faxes on the

phone number for line 4.

If you are talking to someone on line 4 and want that person to fax something to you, change the data port switch to line 2 or line 3, and

give the person on-line the phone number for line 2 or line 3. Your fax machine now can receive calls on line 2, line 3, or line 4.

IMPORTANT: Be sure to switch the fax machine back to the normal line when you are done because outside callers who do not know that you have switched lines

will not be able to reach your fax machine if they dial the line 4 number.

System Veriﬁcation

Use the following procedures to test system conﬁguration and identify possible line connection errors. The phone must be connected to the

power outlet, Line 1 must be connected to the LINE 1 + 2 jack, and the phone must have a phone ID.

VERY IMPORTANT: In order to achieve full system operation (i.e. intercom, page, etc.), Line 1 must be connected and common to all phones on the system. Only

other 25403, 25404, 25413, 25414, or 25415 models are fully compatible.

Other System Phones

1. Press LINE 1.

2. Look at all the other stations. If they all indicate line 1 is being used, the connection is correct.

1. Press the INTERCOM button. The display shows INTERCOM and ENTER CALLING PHONE ID.

2. Enter a phone ID by pressing an Intercom/Memo Log button (1-16). The display shows the phone ID you entered. If the phone ID you

entered is connected to the system, you will hear a ring back tone (call through tone) at your phone. If the phone ID is not connected to

the system, you will hear an error tone. NO ANSWER shows in the display and intercom is cancelled.

Programming the Telephone

This telephone has several programmable functions.

Language

Set the display language to show messages in either English, Spanish, or French.

1. Press the MENU button while in standby mode. The cursor in the display points to SET LANGUAGE.

2. Press the SELECT/SAVE button.

3. Use the < REVIEW > button to scroll to ENGLISH, ESPANOL, or FRANCAIS. The default is English.

4. Press the SELECT/SAVE button to save.

Ringer Tone

The ringers for all four lines may be set independent of one another.

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to SET PHONE OPTIONS.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to SET RING TONE.

5. Press the SELECT/SAVE button. The ringer tone settings for each of the four telephone lines show in the display.

6. Use the < REVIEW > button to scroll to through each ringer tone for LINE 1. A sample ringer tone is generated when you scroll to

individual ringer tones. Choose from eight different tones, or turn the ringer OFF.

NOTE: If you select OFF, the cursor automatically moves to the CID ON/OFF option. Use the < REVIEW > button to select CID ON or OFF. (ON allows the unit to detect

and display CID records for the corresponding telephone line. OFF disables the function for the corresponding telephone.) Press the SELECT/SAVE button.

7. Press the SELECT/SAVE button to save. The cursor automatically moves to LINE 2.

8. Repeat steps 6 and 7 for each telephone line. After you select the ringer tone for LINE 4, press the EXIT button.

NOTE: The line indicators ﬂash for incoming calls even if the ringer is disabled.

Programming the Telephone

Priority Line

The priority line (one of the four lines) has precedence over the other three lines. When you pick up the handset or press the SPEAKER

button, the unit automatically selects the priority line ﬁrst. If the priority line is in use by another party, the unit will select the next

available line.

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to SET PHONE OPTIONS.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to SET PRIORITY LINE.

5. Press the SELECT/SAVE button.

6. Use the < REVIEW > button to scroll to 1, 2, 3, or 4. The default is LINE 1.

7. Press the SELECT/SAVE button to save.

Delay Ring

Use this setting to delay the Central Ofﬁce ring.

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to SET PHONE OPTIONS.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to SET DELAY RING.

5. Press the SELECT/SAVE button.

6. Use the < REVIEW > button to scroll to 0 ring up to 10 rings.

7. Press the SELECT/SAVE button to save.

NOTE: The default Delay Ring is 0. If your system has a phone with the auto attendant ON, we suggest that you set the Delay Ring to 2 rings. This allows the auto

attendant to pick up the incoming call before it rings in.

Phone ID

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to SET PHONE OPTIONS.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to SET PHONE ID.

5. Press the SELECT/SAVE button.

6. Press the SELECT/SAVE button again to automatically set the phone ID, or press any memory button (1-16) to assign a phone ID.

NOTE: The INTERCOM indicator will ﬂash red and green if the ID is not programmed.

NOTE: The Phone ID (01-16) is unique. If you manually select a phone ID that belongs to another unit on the system, NOT AVAILABLE shows in the display. Press

SELECT/SAVE or choose another memory button.

NOTE: If the phone cannot ﬁnd an ID, determine if there are too many phones connected to the system. A maximum of 16 phones can be connected in the

system at one time.

NOTE: You may press the EXIT button at any time to exit , except during the ID search.

Phone Name

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to SET PHONE OPTIONS.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to SET PHONE NAME.

5. Press the SELECT/SAVE button.

6. Use the touch-tone pad to enter the phonebook name (up to 8 characters). More than one letter is stored in each of the number keys.

For example, to enter “Lorraine,” press the 5 key three times for the letter L. Press the 6 key three times for the letter O. Press the 7 key

three times for the ﬁrst letter R. Press the 7 key three times for the second letter R. Press the 2 key once for the letter A. Press the 4 key

three times for the I. Press the 6 key two times for the letter N. Press the 3 key twice for the letter E.

7. Press the SELECT/SAVE button to save.

NOTE: The Phone Name and ID shows in the display when the phone is idle.

Programming the Telephone

Intercom Auto Answer

For “hands-free” operation, the phone can be set to answer an intercom call by automatically activating the speaker.

TIP: You may also use this feature for room monitoring.

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to SET PHONE OPTIONS.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to INTERCOM AUTO ANS.

5. Press the SELECT/SAVE button.

6. Use the < REVIEW > button to choose YES or NO.

7. Press the SELECT/SAVE button to save.

Flash Time

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to SET PHONE OPTIONS.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to SET FLASH TIME.

5. Press the SELECT/SAVE button.

6. Use the < REVIEW > button to scroll through the ﬂash time options. You may choose 100ms or 600ms.

7. Press the SELECT/SAVE button to save.

NOTE: You may press the EXIT button at any time to exit.

Call Alert Tone

Turn on the Call Alert to hear a tone for incoming calls while you are on the telephone. This function notiﬁes you that there is a incoming

call while you are using the phone. If you do not want this tone to disturb your conversation, you can set it to OFF.

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to SET PHONE OPTIONS.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to CALL ALERT TONE.

5. Press the SELECT/SAVE button.

6. Use the < REVIEW > button to scroll to ON or OFF.

7. Press the SELECT/SAVE button to save. The cursor automatically moves to LINE 2.

8. Repeat steps 6 and 7 for each telephone line. After you select a tone for Line 4, press the EXIT button.

No Unknown/Blocked

This option allows you to decide whether the unknown or blocked caller ID calls are saved or not. If you select YES, the unknown or blocked

calls will be saved.

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to SET PHONE OPTIONS.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to NO UNKNOWN/BLOCKED.

5. Press the SELECT/SAVE button.

6. Use the < REVIEW > button to scroll to YES or NO. The default is YES.

7. Press the SELECT/SAVE button to save.

Programming the Telephone

Display Contrast

Adjust the display contrast to one of four contrast levels.

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to SET LCD CONTRAST.

3. Press the SELECT/SAVE button. The MIN and MAX contrast scale shows on the display.

4. Use the < REVIEW > button to adjust the contrast. The display instantly adjusts with each press of the < REVIEW > button.

5. Press the SELECT/SAVE button to save the desired contrast level.

Local Area Code

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to SET AREA CODE.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to LOCAL AREA CODE.

5. Press the SELECT/SAVE button. Enter Number shows in the display.

6. Use the touch tone pad on your phone to enter your local area code.

7. Press the SELECT/SAVE button to save.

NOTE: If you make a mistake, press DELETE to erase all digits.

Regional Area Codes

Depending on your location, you may need to set up to six regional area codes. Setting Regional Area Codes helps the phone determine

the number format to display when a valid CID record is received. Call records matching any of the set regional area codes are displayed

as 10 digits.

NOTE: If the CID telephone number does not display correctly, you may not be able to dial back the number from the Caller ID menu.

You may need to set regional area codes if you reside in an area which:

•

uses multiple area codes

uses overlapping area codes

requires 10-digit dialing.

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to SET AREA CODE.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to REGIONAL AREA CODES.

5. Press the SELECT/SAVE button. All six regional area code ﬁelds and Enter Number show in the display.

6. Use the touch tone pad on your phone to enter up to six regional area codes.

7. Press the SELECT/SAVE button to save.

NOTE: If you make a mistake, press the DELETE button to erase all digits.

Manually Setting the Time and Date

The time and date is automatically set when you receive the ﬁrst CID call. To manually reset the time and date, follow the steps below.

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to SET TIME & DATE.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to SET CLOCK.

5. Press the SELECT/SAVE button, and the cursor moves to the hour ﬁeld.

6. Use the < REVIEW > button to select the hour.

NOTE: AM or PM will be set accordingly with selected hour

Programming the Answering Machine

7. Press the SELECT/SAVE button, and the cursor moves to the minute ﬁeld.

8. Use the < REVIEW > button to select the minutes.

9. Press the SELECT/SAVE button, and the cursor moves to the month ﬁeld.

10. Use the < REVIEW > button to select the month.

11. Press the SELECT/SAVE button, and the cursor moves to the date ﬁeld.

12. Use the < REVIEW > button to select the date.

13. Press the SELECT/SAVE button, and the cursor moves to the day ﬁeld.

14. Use the < REVIEW > button to select the day.

15. Press the SELECT/SAVE button, and the cursor moves back to the hour ﬁeld.

16. Press the EXIT button.

NOTE: You may press EXIT at any step in the process. It is not necessary to re-program the complete time and date if you only want to adjust certain ﬁelds

(i.e.; hour only).

Hour Format

You may set this phone to a 12 or 24-hour format. The default is 12-hour format.

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to SET TIME & DATE.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to SET HOUR FORMAT.

5. Press the SELECT/SAVE button.

6. Use the < REVIEW > button to select 12-HOUR or 24-HOUR.

7. Press the SELECT/SAVE button to save.

Restoring the Default Settings

This feature allows you to reset the menu to the original factory default settings.

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to RESTORE TO DEFAULTS.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to YES or NO.

5. Press the SELECT/SAVE button to save.

Programming the Answering Machine

Pickup Delay

This sets the number of rings before the answering machine picks up the call.

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to ANSWERING MACHINE.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to PICKUP DELAY.

5. Press the SELECT/SAVE button.

6. Use the < REVIEW > button to scroll from 3 rings up to10 rings, or Toll Saver. The default is 5 rings.

7. Press the SELECT/SAVE button to save.

NOTE: Toll Saver can save you the cost of a call when you access your message from another phone.

- If you have new messages, the unit answers after the 3rd ring.

- If you have no new messages, the unit answers after the 5th ring.

- You can hang up after the 3rd or 4th ring and save the pay telephone or long distance charge.

Programming the Answering Machine

Message Length

This sets the maximum recording time for the caller to leave a message when the answering function is on.

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to ANSWERING MACHINE.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to MESSAGE LENGTH.

5. Press the SELECT/SAVE button.

6. Use the < REVIEW > button to scroll to No Limit, 1 minute, 2 minutes, or Greeting Only. The default is No Limit.

7. Press the SELECT/SAVE button to save.

NOTE: If you select Greeting Only, once the call is picked up by answering machine, it will announce “Sorry, no one is available to answer the call. Please call again.”

and then drop the call.

Call Screening

If activated, it allows you to listen to incoming messages as they are recorded.

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to ANSWERING MACHINE.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to CALL SCREENING.

5. Press the SELECT/SAVE button.

6. Use the < REVIEW > button to choose ON or OFF. The default is ON.

7. Press the SELECT/SAVE button to save.

Message Interrupt

If this feature is activated it allows you to pick up the call from another extension while the caller is leaving a message with

the answering system.

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to ANSWERING MACHINE.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to MESSAGE INTERRUPT.

5. Press the SELECT/SAVE button.

6. Use the < REVIEW > button to choose ON or OFF. The default is ON.

7. Press the SELECT/SAVE button to save.

Remote Password

To set the remote access password;

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to ANSWERING MACHINE.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to REMOTE PASSWORD.

5. Press the SELECT/SAVE button.

6. Use the < REVIEW > button to choose ON, OFF or SET UP PASSWORD. The default is OFF and the password is 000.

7. Scroll to SET UP PASSWORD and then press the SELECT/SAVE button to start remote password entry. Use the touch tone pad to enter

your remote password.

8. Press the SELECT/SAVE button to save.

NOTE: If you set the remote password to OFF, the unit will not accept the remote access of answering machine.

Programming the Auto Attendant

Mailbox

Selecting General Mailbox allows you to have the system answer transferred or incoming calls to all 4 lines. Or you may choose Personal

Mailbox to have it answer calls to a selected line only. If you select Transfer Call Only, then the unit will answer only transferred calls.

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to ANSWERING MACHINE.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to MAILBOX.

5. Press the SELECT/SAVE button.

6. Use the < REVIEW > button to choose among the following settings: General, Personal L1, Personal L2, Personal L3, Personal L4, or

Transfer Call Only. If you select “Personal L2”, the unit can answer all the transferred calls and incoming calls from L2 by answering

machine. The default setting is General.

7. Press the SELECT/SAVE button to save.

Programming the Auto Attendant

Auto Attendant will pick up and redirect incoming calls to other extensions in the system per the caller’s input. After you have ﬁnished

programming this feature, press the ATTENDANT button on the base to activate. The button will light when Auto Attendant is activated.

Auto Attendant Pickup Delay

This sets the time delay before the call is picked up by the Auto Attendant.

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to AUTO ATTENDANT.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to AUTO ATT PICKUP.

5. Press the SELECT/SAVE button.

6. Use the < REVIEW > button to scroll from 6 seconds to 13 seconds. The default pickup delay time will depend on the phone ID number.

with ID# set to 1 or 2, the default pickup delay time is 6 seconds

with ID# set to 3 or 4, the default pickup delay time is 7 seconds

with ID# set to 5 or 6, the default pickup delay time is 8 seconds

with ID# set to 7 or 8, the default pickup delay time is 9 seconds

with ID# set to 9 or 10, the default pickup delay time is 10 seconds

with ID# set to 11 or 12, the default pickup delay time is 11 seconds

with ID# set to 13 or 14, the default pickup delay time is 12 seconds

with ID# set to 15, or 16, the default pickup delay time is 13 seconds

7. Press the SELECT/SAVE button to save.

TIP: Set different Auto Attendant pickup delay times in different 25415’s

Set Day Time for Auto Attendant

The Auto-Attendant Day outgoing message will be played during the Day Time you program. The pre-recorded announcement is: “Hello,

please enter your party’s extension. If you do not know the extension number, press zero (0), zero (0).”

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to AUTO ATTENDANT.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to SET DAY TIME.

5. Press the SELECT/SAVE button, and the curser moves to the hour ﬁeld. The default is 8:00 AM.

6. Use the < REVIEW > button to select the hour. AM or PM will be set accordingly with the selected hour.

7. Press the SELECT/SAVE button to save, and the curser moves to the minutes ﬁeld.

8. Use the < REVIEW > button to select the minute.

9. Press the SELECT/SAVE button to save.

10. Press the EXIT button.

Programming the Auto Attendant

Set Night Time for Auto Attendant

The Auto-Attendant Night outgoing message will be played during the Night Time you program. The pre-recorded announcement is: “Hello,

please enter your party’s extension. If you do not know the extension number, press zero (0), zero (0).”

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to AUTO ATTENDANT.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to SET NIGHT TIME.

5. Press the SELECT/SAVE button, and the curser moves to the hour ﬁeld. The default is 5:00 PM.

6. Use the < REVIEW > button to select the hour. AM or PM will be set accordingly with the selected hour.

7. Press the SELECT/SAVE button to save, and the curser moves to the minutes ﬁeld.

8. Use the < REVIEW > button to select the minute.

9. Press the SELECT/SAVE button to save.

10. Press the EXIT button.

Set Night Time ON / OFF

If this feature is set to ON, the Auto Attendant Day Greeting will play during the time you designate as Day Time, and during the time you

have designated as Night Time, the Auto Attendant Night Greeting will be activated.

If this feature is set to OFF, the unit will play the Auto Attendant Day Greeting at all times.

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to AUTO ATTENDANT.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to NIGHT TIME ON/OFF.

5. Press the SELECT/SAVE button.

6. Use the < REVIEW > button to choose ON or OFF. The default is OFF.

7. Press the SELECT/SAVE button to save.

Set Weekend Greeting

There are two options for you to select from for your Weekend Greeting. The Night Greeting option will play your Night Greeting from

Friday night until Monday morning, the Same As Weekday greeting will play your weekday greeting throughout the weekend.

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to AUTO ATTENDANT.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to WEEKEND GREETING.

5. Press the SELECT/SAVE button.

6. Use the < REVIEW > button to choose NIGHT GREETING or SAME AS WEEKDAY. The default is SAME AS WEEKDAY.

7. Press the SELECT/SAVE button to save.

Set Valid ID

When auto attendant is turned on, the call can be forwarded to any listed extension number.

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to AUTO ATTENDANT.

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to SET VALID ID.

5. Press the SELECT/SAVE button.

6. Use the MEMORY LOG number key (M1 to M16) to add or delete the corresponding listed extension number.

7. Press the SELECT/SAVE button to save.

Basic Operation

Your phone provides the convenience of accessing four separate telephone lines, each obtained from the telephone company and each

having its own phone number. This is generally applicable to small ofﬁces. It provides for 16 telephones (or stations) to share multiple lines.

Each station is interconnected to all others by an intercom.

Making Calls with the Handset

1. Pick up the handset and the phone automatically selects the priority line. If the priority line is occupied, it selects an open line.

Pick up the handset and press a LINE button to select a line.

2. Wait for a dial tone, then dial a phone number.

3. Hang up the handset when ﬁnished.

Making Calls with the Speakerphone

1. Press the SPEAKER button and the phone automatically selects the priority line. If the priority line is occupied, it selects an open line.

Press a LINE button to select a line.

2. Wait for a dial tone then dial a phone number.

3. Press SPEAKER button when ﬁnished.

NOTE: Only one-way conversation is possible in speakerphone mode. When you are speaking, you are transmitting. When you are listening, you are receiving. You

can’t do both at the same time. The phone will automatically switch between transmitting and receiving depending on the level of the voice or the room noise

picked up by the speakerphone mic.

NOTE: If a line goes off-hook, the call timer counts time until all the lines go on hook. The timer serves for 4 lines.

Making Calls with the Optional Headset

1. Connect the headset plug to the HEADSET jack on the side of the base.

2. Adjust the headset to rest comfortably on top of your head and over your ear.

3. Move the microphone to approximately 2 to 3 inches from your mouth.

4. Press the HEADSET button and the phone automatically selects the priority line. If the priority line is occupied,

it selects an open line.

5. Wait for a dial tone, then dial a phone number.

6. Press HEADSET when ﬁnished.

CAUTION: Use only the ATLINKS USA, Inc. 5-2425 headset that is compatible with this unit.

NOTE: If the headset is not connected (or if not completely inserted into headset jack), an error tone is heard when the HEADSET button is pressed.

Pre-dialing

1. With the phone idle and the handset on the cradle, manually enter the telephone number. The telephone number shows in the display.

2. Press the DIAL or SPEAKER button, or lift the handset to take a line, and the telephone number is automatically dialed.

Answering Calls

If you receive a call on the priority line,

1. Pick up the handset (handset mode), OR

2. Press the SPEAKER button (speakerphone mode), OR

3. Press the HEADSET button (headset mode).

4. When ﬁnished, hang up the handset, or press the SPEAKER button or press the HEADSET button.

If you receive a call on a line other than the priority line,

1. Pick up the handset and press the corresponding line button (handset mode), OR

2. Press the SPEAKER button and press the corresponding line button (speakerphone mode), OR

3. Press the corresponding line button, and then press the HEADSET button (headset mode).

4. When ﬁnished, hang up the handset, or press the SPEAKER button, or press the HEADSET button.

NOTE: Whether you are making or receiving a call, the caller is disconnected if you press another line without putting the call on hold ﬁrst.

Basic Operation

Switching Between the Speakerphone, Handset, and Headset

To switch to the speakerphone, press SPEAKER. The speakerphone indicator turns on. Put handset back in cradle.

To switch to the handset, pick up the handset. The speakerphone or headset turns off.

To switch to the headset, press the HEADSET button to enable the headset, and the headset indicator turns on. Hang up the handset.

Mute

To have a private, off-line conversation, use the MUTE feature. The party on the other end of the line cannot hear you, but you can still hear

them.

1. Press MUTE to activate the mute feature. The mute indicator turns on.

2. Press MUTE again to turn it off.

NOTE: Switching from speakerphone to handset cancels mute.

Do Not Disturb

This feature is set at individual telephones to disable (silence) an incoming ring signal, intercom ring, or page. When there is an incoming

call or an intercom call, the status indicators function as normal but the phone will not ring.

1. When the unit is idle, press the PRIVACY button. The Privacy indicator ﬂashes and the last setting is displayed.

2. Use the < REVIEW > button to select the duration. You may choose from 15 minutes, 30 minutes, 45 minutes, 1 hour, or 2 hours and

increase the duration by 1 hour intervals up to 24 hours.

3. Press the SELECT/SAVE button to conﬁrm. The indicator blinks and the display shows how long the ringer will be disabled.

4. To cancel, press PRIVACY again or hang up the handset.

NOTE: If Intercom Auto Answer is turned ON, the unit automatically answers the intercom call even if the Do Not Disturb function is activated.

Hold

Placing a Call on Hold

Press the HOLD button to put the line in use on hold. The line indicator for the line on hold ﬂashes green. The phone emits a beep every 30

seconds as a reminder. At the other stations, the indicator blinks red but no beep is heard.

NOTE: If you put a call on HOLD while in PRIVACY mode, no one but you can access the line on hold. Anyone trying to access the line receives an error tone.

Releasing a Call from Hold

Press the HOLD button or the corresponding LINE button to release hold.

NOTE: If you want to change modes, lift the handset to switch to the handset, or press the HEADSET button to use the headset.

NOTE: The call on hold can be picked up at any station using this procedure.

Flash

Use the FLASH button to activate custom calling services such as call waiting or call forwarding, which are available through your local

phone company.

Redial

1. Pick up the handset (handset mode), or press the SPEAKER button (speakerphone mode), or press the HEADSET button (headset mode)

and the priority line is automatically selected,

Press a line button to select other line.

2. Press the REDIAL/FORMAT button

NOTE: The redial function will not operate if the number to be redialed contains more than 32 digits. If the number is longer than that, you will hear an error tone.

Reviewing the Redial Numbers

Your phone records up to six previously dialed phone numbers.

1. When the phone is idle, press the REDIAL/FORMAT button.

2. Use the < REVIEW > button to view the last six previously dialed numbers.

3. While the preferred number is displayed, pick up the handset or press the SPEAKER, DIAL, or a line button to dial the phone number.

NOTE: If you do not select a line button, the line is automatically seized and the number is dialed accordingly.

Basic Operation

Transferring a Call to Another Station

1. With the caller on the line, press the TRANSFER button.

2. Press the INTERCOM/MEMORY LOG button (1-16) for the station you want to transfer the call to. The line’s indicator blinks yellow until

the party picks up the transferred call. Once the call is picked up, the indicator stays red. The indicator on the receiving party’s line

rapidly ﬂashes red and rings during call transfer.

• If the transferred call is not picked up at the other station within 45 seconds. The transfer cancels, the line is put on hold, and the line

indicator ﬂashes green.

• If the party at the other station doesn’t pick up the transferred call, and you want to attempt to transfer to another station, press the

line button and repeat the transfer process from step 1.

Receiving a Transferred Call from Another Station

If a call is transferred to your station, the line indicator ﬂashes red. To answer the call, press that line button.

If you are on the line when a call is transferred to you, you will hear beeps to alert you of the incoming call. Put your current call on hold by

pressing HOLD, and then pick up the incoming call by pressing the corresponding line button.

NOTE: During the transfer, the only two stations that can access the line are: a) the transferring station, or; b) the station receiving the transfer.

VERY IMPORTANT: To transfer a call from one station to another, the two stations should be connected to the same line.

Privacy

While in use, a line can be secured so that no one else can listen to the conversation. This feature only applies to 25403, 25404, 25413,

25414, and 25415 phones. However, other phone which are not compatible with these models can still access the line.

Providing Privacy

At any time during a conversation, you can use the privacy feature to secure the line.

1. While on a line, press the PRIVACY button. The indicator turns on.

2. To cancel, press PRIVACY again or hang up.

NOTE: If you put a call on hold while in privacy mode, no one but you can access the line on hold.

Volume

The ringer, speaker, and handset/headset volume is set independently with the VOLUME up and down buttons. There are 8 possible volume

settings per mode. The volume indicator scale is displayed during volume adjustment.

Ringer Volume

1. While the phone is on the hook, press the VOLUME up or down button. The phone rings according to the current setting.

2. Tap the up or down button to adjust the volume one level at a time. The phone stores the setting after the last button press.

NOTE: To turn the ringer off, on, or change the ringing pattern, see Setting the Ringer Tone.

Speakerphone, Handset, and Headset Volume

While the phone is in use, during the desired mode, press the VOLUME up or down buttons until you reach a comfortable listening level. The

phone stores the setting after the last button press.

Conference Calls

This feature allows you to have a 3-way conversation using any combination of 2 lines.

To connect and conference

1. To make a call, press the line you want and dial the telephone number. If you already have someone on the line, skip to step 2.

2. Press the HOLD button to place the call on hold.

3. Press another line button and dial the telephone number of the party you want to conference with.

4. Press the CONFERENCE button.

5. Speak to both parties.

NOTE: If you have more than one line on hold, and you want to have a conference call, you must ﬁrst select the line on which you want to conference.

Intercom Operation

To disconnect one party:

Press the line button for the person you want to continue speaking with, and the other party is automatically disconnected.

To disconnect both parties:

Hang up the handset, or press the SPEAKER or HEADSET button.

NOTE: If you press the HOLD button to put them on hold ﬁrst, you may then disconnect from each party individually.

Intercom Calls

One-Touch Intercom

NOTE: If the INTERCOM indicator is turned on (solid red), the intercom is in use. You must wait until the indicator turns off before making an intercom call.

1. Press the INTERCOM/MEMORY LOG button (1-16) for the station you want to intercom with. The SPEAKER turns on.

Alternately, you may press the INTERCOM button, then press the INTERCOM/MEMORY LOG button (1-16) for the stations you want to

intercom with. The speakerphone automatically turns on.

NOTE: If you want to switch to the handset, pick it up and continue speaking. To switch to the headset press the HEADSET button.

NOTE: The handset, headset, or speakerphone cannot be active when an intercom call is initiated (the handset should be on the cradle and the speakerphone and

headset turned OFF.)

NOTE: To abort intercom call, press SPEAKER button.

2. To end the intercom call, hang up.

NOTE: If the receiving station does not answer within 45 seconds, the intercom call is cancelled. You will hear an error tone and NO ANSWER shows in the display.

NOTE: If the intercom is in use. You will hear an error tone and ERROR INHIBITED shows in the display.

Answering an Intercom Call

When you receive an INTERCOM call, the INTERCOM indicator ﬂashes red, and the display shows the caller’s name and phone ID.

NOTE: If you want to answer with the speakerphone, press the INTERCOM or SPEAKER button. If you want to answer by headset, press the HEADSET button (the

headset must be connected). To answer by handset, lift the handset.

NOTE: Press SPEAKER or lift the handset to automatically select a party. If you receive an incoming call and intercom call at the same time the unit automatically

selects the ringing line.

Intercom Hold

1. Make an intercom call or answer an intercom call.

2. Press the HOLD button. The Intercom indicator ﬂashes green.

NOTE:

• When the intercom is on hold, you may not receive another intercom.

• If the other party terminates intercom, intercom hold is also released.

Intercom Conference Calls

This feature allows you to have a 3-way conversation using the intercom feature and an open line.

1. Place a call or make an intercom call.

2. Press the HOLD button.

3. Place a call on another line or make an intercom call.

4. Press the CONFERENCE button.

5. Speak to both parties.

NOTE: If you have more than one party on hold (telephone line or intercom), you must select the line for the party you want to conference with.

To disconnect one party:

Press the line or intercom button for the person you want to continue speaking with, and the other party is automatically disconnected.

To disconnect both parties:

Hang up the handset, or press the SPEAKER button.

NOTE: If you press the HOLD button to put them on hold ﬁrst, you may then disconnect from each party individually.

Caller ID

Paging All Stations

1. Lift the handset.

2. Press the PAGE button and listen for the beep. The other stations not in use automatically activate their speakerphones and receive your

page.

3. Speak into the handset. You have 30 seconds to page in this mode. After 30 seconds, the page is cancelled.

4. When ﬁnished, hang up the handset.

NOTE: You will not receive a page when Do Not Disturb is turned on.

NOTE: Paging can be done with optional headset. plug in headset, press HEADSET button, the press PAGE button

Caller ID

Summary Screen

The summary screen shows the current time, current date, number of CID records to be reviewed and total number of records saved to CID

memory. It is displayed until any button is pressed. Within 60 seconds of receiving a new call, the new caller information is displayed.

Phone ID

Name of phone

(01)JOHN

Battery indicator

CID records waiting to

be reviewed

00NEWCALLS

ANS

OFF

00Total CALLS

Time and date

12:34 PM 12/25 SUN

Number of records in CID memory

Receiving and Storing CID Records

This unit receives and displays information transmitted by your local phone company. This information can include the phone number, date

and time; or the name, phone number, date and time. The unit can store up to 99 calls for later review. When the memory is full, a new call

automatically replaces the oldest call in memory. NEW appears in the display for calls received that have not been reviewed. The line number

for the call received is also displayed.

In case multiple incoming calls come in at the same time, the CID information is displayed according to the unit’s priority line setting.

Example: the priority line is 3.

Reviewing CID Records

INCOMING CALL

• Press the < REVIEW > button to scroll through the call records.

NOTE: If you press the > button, the oldest record shows in the display. If you press the < button, the most

recent record shows in the display.

JOHN SMITH

1-317-123-4567

•

When you scroll to the start/end of the list, START/END appears in the display.

12:34 PM 12/25

Saving a CID Record to the Intercom/Memory Log or to Phone Book Memory

1. While a name and telephone number shows in the display, if you need to edit the

information, press the SELECT/SAVE button and follow the steps for Storing a Name and

Number in Memory.

L3: 555-1234

L1: 1-317-123-4567

2. If you do not need to edit the name or number, press the STORE button.

3. To store data in the Phone Book Directory, press the DIRECTORY button,

L2:

L4:

To store data in the Intercom/Memory Log, press a memory log button (1-16).

Deleting a CID Record

To delete the record shown in the display, press the DELETE button once.

Deleting All Call Records

CID REVIEW

NEW

This feature allows you to clear all CID records at once.

1. While viewing a CID record, press and hold the DELETE button. PRESS DELETE AGAIN

JOHN SMITH

1-317-123-4567

12:34 PM 12/25

CLEAR ALL CALLER ID shows in the display.

2. Press the DELETE button again to conﬁrm.

Memory

Dialing Back

When reviewing CID records, you can dial back the numbers showing on the display by pressing the DIAL button.

If You Programmed Your Local Area Code

1. Use the < REVIEW > button to display the number you want to dial.

2. If you see a number with 7 digits (i.e.555-1234), then the call was received from within your area code. However, this does not guaran-

tee the call is a local call. If you see a number with 11 digits (i.e.1-234-555-1234), then the call received was not from your area code.

3. To adjust the phone number format, use the REDIAL/FORMAT button. For instance, a 7-digit local number sometimes cannot be dialed

because it requires a 10-digit or 11-digit format. Use the REDIAL/FORMAT button to scroll through 7, 10 and 11-digit numbers.

7-digits:

7-digit telephone number (i.e.555-5555)

10-digits:

11-digits:

3-digit area code +7-digit telephone number (i.e.425-555-5555)

long distance code 1 +3-digit area code +7-digit telephone number (i.e. 1-425-555-5555)

4. To dial the displayed number, select a line or press DIAL again.

If You Did Not Program Your Local Area Code

1. Use the < REVIEW > button to display the number you want to dial. You will only see 10-digit numbers (i.e.234-555-1234).

2. Press DIAL to dial back. You may adjust the number format by pressing the REDIAL/FORMAT button before dialing.

Call Waiting Caller ID

This feature allows you to see who is calling when you hear the call waiting beep. The caller identiﬁcation information appears in the

display after you hear the tone.

• Press the FLASH button to put the person to whom you’re talking on hold and answer the incoming call.

IMPORTANT: To use all the features of this unit, you must subscribe to either the standard Name/Number Caller ID Service or Caller ID with Call Waiting Service. To

know who is calling while you are on the phone, you must subscribe to Caller ID with Call Waiting Service.

Memory Log and Phone Book (Directory) Memory

You may store data in the Phone Book Directory (up to 94 memories) or an INTERCOM/MEMORY LOG (16 buttons located to the right of the

number pad on the base). The Phone Book and each INTERCOM/MEMORY LOG stores up to 21 characters and 32 digits.

Storing a Number and Name in Memory

NOTE: To cancel the storing procedure at any time, press EXIT.

1. Press the STORE button. ENTER NUMBER is displayed.

2. Use the touch tone pad on your telephone to enter the telephone number you want to store. The numbers you enter show in the display.

NOTE: If you make a mistake, use the < REVIEW > button to move the cursor to the incorrect digit, and press the DELETE button to delete.

3. Press SELECT/SAVE. ENTER NAME is displayed.

4. Use the touch-tone pad to enter a name (up to 21 characters). More than one letter is stored in each of the number keys. For example,

to enter Bill Smith, press the 2 key twice for the letter B. Press the 4 key 3 times for the letter I. Press the 5 key 3 times for the letter L.

Press the 5 key 3 times for the second letter L, and press the 1 key to insert a space between the ﬁrst and last name. Press the 7 key 4

times for the letter S; press the 6 key once for the letter M; press the 4 key 3 times for the letter I; press the 8 key for the letter T; press

the 4 key twice for the letter H.

NOTE: If you make a mistake, use the < REVIEW > button to move the cursor to the incorrect digit, and press the DELETE button to delete.

5. Press STORE button. ENTER LOCATION is displayed.

6. Enter memory location:

Press the DIRECTORY button to save the record in the Phone Book memory,

Press a INTERCOM/MEMORY LOG button (1-16) to save the record in that memory location.

NOTE: If there is a record stored in selected memory location “OVERWRITE?” shows in the display. Press STORE to conﬁrm overwrite or press the EXIT button, then

select a new location.

7. Repeat steps 1-6 for any additional names and numbers you want to store, up to 94, in phone book memory.

NOTE: The storage procedure automatically cancels after 30 seconds if no keys are pressed.

Memory

Reviewing Phone Book (Directory) Memory

1. Press the DIRECTORY button. The ﬁrst memory in the phone book is displayed (memories are stored in alphabetical order).

2. Use the < REVIEW > button to scroll through the phone book memories, or use the touch tone pad on your phone to enter the cor-

responding letters for the memory you want to review. For example, press the 5 key to display phone book memories that start with the

letter J. Press the 5 key twice to go to memories starting with the letter K.

3. Press the EXIT button when you are ﬁnished reviewing memories.

Reviewing the Intercom/Memory Log (memory location)

1. Press the DIRECTORY button.

2. Press the INTERCOM/MEMORY LOG button (1-16).

3. Press the EXIT button when you are ﬁnished reviewing memories.

Editing a Name or Number Stored in Phone Book (Directory) Memory

1. Press the DIRECTORY button.

2. Use the < REVIEW > button to scroll to the desired memory record.

3. Press the SELECT/SAVE button and edit the content according to the steps in the Storing a Name and Number in Memory section.

Editing a Name or Number Stored in the Intercom/Memory Log (Memory Location)

1. Press the DIRECTORY button.

2. Press the INTERCOM/MEMORY LOG button (1-16).

3. Press the SELECT/SAVE button and edit the content according to the steps in the Storing a Name and Number in Memory section.

Storing the Last Number Dialed

1. When the phone is idle, press the REDIAL/FORMAT button.

2. Use the < REVIEW > button to view the last six previously dialed numbers.

3. While viewing the desired number, press the SELECT/SAVE button twice.

4. Add the name as explained in the Storing A Name and Number in Memory section.

5. Press the STORE button. ENTER LOCATION shows in the display.

6. Press the DIRECTORY button to store the redial number in the Phone Book memory or press an INTERCOM/MEMORY LOG button (1-16)

to store the redial number in that memory location.

Storing a Pause in Memory

Press the #PAUSE button twice to insert a pause in the dialing sequence of a stored telephone number when a pause is needed (for example,

when you must dial a 9 to get an outside line or when you must enter codes to access your bank’s information line).

Dialing a Stored Number

1. Pick up the handset, or press SPEAKER to automatically select a line. Or press the line you want to use.

2. Wait for a dial tone.

3. Press the INTERCOM/MEMORY LOG button (1-16) for the person you want to call. The number automatically dials.

1. Press the DIRECTORY button.

2. Use the < REVIEW > button to scroll through the phone book memories, or use the touch tone pad to enter the corresponding letters

for the memory you want to review. For example, press the 5 key to display phone book memories that start with the letter J. Press the 5

key twice to go to memories starting with the letter K.

3. Press the DIAL button. The number automatically dials.

Memory Delete/Clear

To delete a Phone Book memory:

1. Press the DIRECTORY button.

2. Use the < REVIEW > button to scroll to the memory you want to delete.

3. Press the DELETE button to delete. DELETE -DELETE AGAIN shows in the display.

4. Press the DELETE button again to conﬁrm.

Answering System Operation

To delete an INTERCOM/MEMORY LOG:

1. Press the DIRECTORY button.

2. Press the corresponding button (1-16) for the Intercom/Memory Log you want to delete.

3. Press the DELETE button to delete, DELETE -DELETE AGAIN shows in the display.

4. Press the DELETE button again to conﬁrm.

NOTE: Press the EXIT button to cancel the “delete” function.

Clear All Memories

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to SET PHONE OPTIONS.

3. Press the SELECT/SAVE button.

4. Use < REVIEW > button to scroll to CLEAR ALL MEMORIES.

5. Press the SELECT/SAVE button.

6. Use the < REVIEW > button to scroll to Yes or No, No is the default.

7. Press the SELECT/SAVE button to conﬁrm.

NOTE: If you select YES, all the directory memories and direct access memories are cleared.

Chain Dialing

This process allows you to dial a succession of stored numbers from separate memory locations. This is useful when you must dial several

sequences of numbers, such as with frequent calls via a telephone company long distance provider.

For example

Memory location

Local access number of long distance company

Authorization code (ID)

Long distance phone number

1. Press the line you want.

2. Press memory location 6.

3. Press memory location 7.

4. Press memory location 8.

Answering System

Answering Machine

You can set one or more additional phones to act as an Answering Machine (up to 16 units in the system), each Answering Machine can

pick up only one line at a time. To prevent several Answering Machine units picking up the same call, you should assign different pickup

delay times for each Answering Machine unit.

The Answering Machine can store approximately 60 minutes of messages, memos, and all the announcements, for a total of up

to 99 messages.

Turning the Answering System On/Off

Press the ANSWERER button to switch this function on or off. The ANSWERER light is lit when the function is activated.

Recording a Greeting

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to ANSWERING MACHINE

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to RECORD GREETING.

5. Press the SELECT/SAVE button.

6. Wait for the beep. Then speak toward the phone in a normal tone of voice. You have a maximum 30 seconds to record your greeting

7. Press the SELECT/SAVE button to save, and the user’s recorded greeting will playback once. (The default greeting is “Please leave a

message after the tone.”)

Answering System Operation

Playback and Erasing a Greeting

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to ANSWERING MACHINE

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to PLAYBACK GREETING.

5. Press the SELECT/SAVE button.

6. The system plays the previously recorded greeting.

7. To erase the recorded greeting, press DELETE button during greeting playback. Press DELETE again to conﬁrm the deletion. Then the de-

fault greeting will playback once after deletion.

8. To stop playback, press EXIT.

Recording Incoming Messages

The unit will answer incoming calls or routed calls after X rings (pickup delay set in MENU) and play the outgoing greeting. After hearing

the greeting followed by a long beep, the caller can leave a message. The message counter shows new number of messages.

If there is a new message recorded in the unit, the “NEW MESSAGE” indicator will blink.

Note: Your unit will record a message up to the maximum length of time you set as long as the caller continues speaking. To save recording capacity, your unit will

automatically stop recording after 7 seconds of silence or if there is a steady dial tone for 7 seconds.

Your unit can record up to 60 minutes of incoming messages. The maximum recording time for each incoming message can be set in MENU.

Monitoring Incoming Calls

Whenever an incoming message is being recorded you can hear it through the speaker if Call Screening is on. To take the call, pick up the

handset and the system stops recording. You can interrupt the recording from another extension, if you have Message Interrupt set to ON in

the menu.

Memo Recording

1. Press and hold the MEMO button for 2 seconds until you hear a beep.

2. After the beep, speak toward the phone in a normal tone of voice and record your memo.

3. To stop recording, press MEMO button again or press EXIT button. This is considered standard message and will be included in the

message counter.

Two-Way Recording

While using the handset or headset, you can record a phone conversation.

1. While on a call using the handset or headset, press MEMO to begin recording the conversation.

2. Press MEMO again or press EXIT button to stop recording. This is considered standard message and will be included in the

message counter.

Note: Before start to record the phone conversation, suggest you to tell the party you are speaking to that the conversation will be recorded.

Message Playback

In idle mode, press the PLAY button once. The unit starts to playback the messages.

If the unit has new messages, only the new messages will be played, otherwise all messages will be played. Unit will play messages to the

end, then return to standby mode.

During each message playback, you can press REVIEW > button to skip the current message OR press < REVIEW button to replay the mes-

sage playing.

If there are no messages, the unit will announce “You have NO messages”.

Deleting Messages

To delete messages:

1. Press the PLAY button while in idle mode.

2. Use the < REVIEW > button to scroll to the message you want to delete.

3. Press DELETE button and MESSAGE XX DELETE? shows in the display.

4. Press the DELETE button again to conﬁrm.

Answering System Operation

To delete all the messages:

1. Press and hold the DELETE button for 2 seconds during message playback or while in standby mode. DELETE ALL MESSAGES? shows in

the display.

2. Press the DELETE button again to conﬁrm the deletion.

NOTE: You cannot delete ALL messages while you are playing the new messages. You can only delete the messages one by one during playback.

Accessing the Answering System from Another Location

You can access many features of this answering system when you are away from your phone. To access your mailbox, you must turn on the

remote function and set a three-digit remote password (see Remote Password section.)

Connecting with the Answering System

1. Call your phone number.

2. After the unit answers, enter your three digit password after playback of the greeting.

3. If the password was entered correctly, the Voice Menu will direct you to press the following buttons on your keyboard:

Press 2 to play messages, press 2 again to stop.

Press 3 to skip.

Press 1 to review.

Press 0 while playing a message to erase.

Press 4 to turn on and off.

Press 6 to play greeting.

Press 9 to record a greeting, press 9 again to stop taking message.

Press 7 to review menu again.

4. Enter the remote commands.

5. To exit remote operation, hang up. The system will automatically disconnect the call if the user does not enter a command

within 10 seconds.

Toll Saver Operation

This system has a built-in automatic toll saving feature to let you know if you have received any new messages before it answers, thus sav-

ing you on long distance costs.

IF YOU HAVE SELECTED THE TOLL SAVER FUNCTION IN PICKUP DELAY, when calling the system from a remote location to check your mes-

sages, listen to the number of rings.

1. NO New Messages Received

If the phone rings more than three times, there are no new messages. You can hang up on the fourth ring before system answers, and

save the cost of the call. Otherwise system will answer the call after ﬁfth ring.

2. New Messages Received

If the system answers after only 3 rings, you have received new messages. Refer to Connecting with Answering System for remote in-

structions.

Auto Attendant

You can set this phone to function as the Auto-Attendant. A phone designated as an Auto-Attendant will pick up and redirect incoming

calls to other extensions in the system. Each Auto-Attendant can pick up only one line at a time, so you may wish to have more than one

Auto-Attendant within your system. You can designate up to 16 Auto-Attendants in your system. To prevent several units picking up the

same call at once, you should assign different pickup delay times for each Auto-Attendant units.

Turn Auto Attendant On/Off

Press the ATTENDANT button to switch this function on or off. The ATTENDANT light is lit when the function is activated.

Auto Attendant Sequence for Callers

When Auto-Attendant is on, this phone automatically picks up a ringing line after the pickup time you programmed, and plays the

designated Auto-Attendant greeting. When a caller enters an extension number after hearing the greeting, the Auto-Attendant transfers

the call to that extension. If the requested extension doesn’t pick up within 45 seconds, the Auto-Attendant takes the call back and plays

the general greeting. If Auto-Attendant unit is in use, the call will be placed on hold.

Auto Attendant Operation

If the caller does not enter an extension number after hearing the message, the Auto-Attendant waits about 5 seconds and replays the

ATTENDANT OGA (out-going announcement) for the caller. If the caller still does not enter an extension number within 5 seconds;

a) the Greeting Only OGA “Sorry, no one is available to answer the call. Please call again.” will be played if the answering machine

is set to off.

b) the greeting “Welcome to general delivery mailbox. Please leave your name and phone number after the tone.” will be played if

the answering machine is set to on and mailbox sets to general.

If the caller presses 00 after hearing the message, the Auto-Attendant Auxiliary Outgoing Message plays. The caller can then enter an

extension number, and the call will be redirected.

Recording Auto Attendant Greetings

There are three different Auto Attendant outgoing messages. They are Day Greeting, Night Greeting and Auxiliary Greeting.

Day Greeting is played during the time you set as day time. The Default Day Greeting is “Hello, please enter your party’s extension. If you do

not know the extension number, press zero (0), zero (0).”

Night Greeting is played during the time you set as night time. The Default Night Greeting is “Hello, please enter your party’s extension. If

you do not know the extension number, press zero (0), zero (0).”

Auxiliary Greeting is played when an outside caller presses the “0” key twice after hearing the Day or Night message. It is supposed to be

recorded by you to tell the caller about the extension number list. The Default Auxiliary Greeting is “Please enter your party’s extension.”

You can follow the procedures listed below to record the your own greeting.

NOTE: When recording your own Day or Night Greeting be sure to include the following statement to inform your callers of the extension list. “If you do not know

the extension number, press zero (0), zero (0).”

NOTE: When recording your own Auxilary Greeting you should include your extension listing. For example, “To reach Peter Jones, extension #1, for Mary Smith,

extension #2, etc.

1. Press the MENU button while in standby mode.

2. Use the < REVIEW > button to scroll to AUTO ATTENDANT

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to RECORD GREETING,

5. Press the SELECT/SAVE button.

6. Use the < REVIEW > button to scroll to DAY GREETING, or NIGHT GREETING or AUXILIARY GREETING.

7. Press the SELECT/SAVE button.

8. Wait for the beep. Then speak toward the phone in a normal tone of voice.

9. Press the SELECT/SAVE button to save, and the recorded greeting will be playback once.

Playback and Erasing Auto Attendant Greetings

1. Press the MENU button.

2. Use the < REVIEW > button to scroll to AUTO ATTENDANT

3. Press the SELECT/SAVE button.

4. Use the < REVIEW > button to scroll to PLAYBACK GREETING.

5. Press the SELECT/SAVE button.

6. Use the < REVIEW > button to scroll to DAY GREETING, or NIGHT GREETING, or AUXILIARY GREETING.

7. Press the SELECT/SAVE button.

8. The system plays the previously recorded greeting.

9. To erase the recorded greeting, press DELETE button during greeting playback. Press DELETE again to conﬁrm the deletion. The default

greeting will play back once after deletion.

NOTE: The default greeting cannot be deleted.

10. To stop playback, press EXIT.

Using Multiple Auto Attendants

An Auto Attendant is in use and cannot answer the incoming call when someone at that extension is:

- accessing messages, or

- using any of the lines to make or answer a call, or

Troubleshooting Guide

- on an intercom call, or

- programming the phone, or

- when a message is being recorded at that extension.

It is preferable to set one or more additional phones to act as Auto Attendant for occasions when the primary Auto Attendant is turned off

or in use. The primary Auto Attendant is the unit having the shortest pickup time, others would have longer pickup times.

Display Messages

The following special messages indicate the status of a message or the unit:

00 TOTAL CALLS

The Caller ID memory log is empty.

UNKNOWN CALLER

The incoming call does not have Caller ID service or their service area is not linked to yours. If UNKNOWN CALLER

appears along with a calling number, the name information for that number was not available.

BLOCKED CALL

INCOMPLETE DATA

NO DATA

The caller is registered as “Private Number ”and their Caller ID information is withheld.

Caller information has been interrupted or corrupted during transmission.

No Caller ID signal has been detected, or Caller ID service has not been activated.

You are at the beginning or the end of the Caller ID memory log.

Battery power level is low.

START/END

Operation By Battery

If the power cord is not plugged into the unit, and the battery is available, the unit enters Battery Operation Mode. In this mode, the unit

fully supports all operational features, except the intercom call function and cordless handset.

NOTE: Under battery operation mode, the RF module (optional for use with cordless handset) is not supported.

Operation without Power

If the power cord is not plugged into the unit and no battery is installed, the unit enters into No Power Operation mode. in this mode, the

user may:

1) use the handset to manually make a call on line 1 only,

2) answer a call on line 1 with the handset.

Cordless Phone Option

It is possible to enhance your phone to a cordless feature with the additional purchase of the H5400 accessory handset and module. The

H5400 is packaged with an RF module, when the module is properly inserted into the back of the 25415 base, the antenna icon on the

display will illuminate. After registration (see user guide of model H5400) you may use your cordless handset with your phone system.

Troubleshooting Guide

No dial tone

•

Check or repeat installation steps:

Make sure the telephone line cords are connected to the phone and the wall jack. Make sure the line cords are not damaged.

Make sure the hook switch pops up when the handset is lifted.

Check the SPEAKER button. Make sure the indicator is off.

Disconnect the phone from the wall jack and connect another phone to the same jack. If there is no dial tone in the second phone, the

problem might be your wiring or local service.

You cannot be heard by the other party.

•

Make sure the handset or headset cord is inserted properly and securely.

Make sure the MUTE feature is not turned on.

Phone does not ring.

•

Make sure the ringer is turned on.

Make sure the Do Not Disturb feature is not activated.

You may have too many extension phones on your line. Try unplugging some phones.

See solutions for “No dial tone.”

Troubleshooting Guide

Incoming voice too low or none at all.

•

Check volume setting.

Memory dialing doesn’t work

•

Did you program the memory location keys correctly?

Did you follow proper dialing sequence?

Battery icon is blank or shows only one bar

The 4 “AAA” batteries need replacing or are improperly installed or not installed at all.

Intercom does not function correctly

•

Make sure line 1 is connected properly and common to all phones on the system.

Make sure all phone ID’s (station numbers) involved have been assigned.

Transfer does not function correctly

Make sure receiver phones (stations) have same line connected.

Intercom indicator turns red and green alternately

•

The station address needs to be re-assigned due to a duplicate station address in the system.

See “Changing the Phone ID (Station Address)”.

General Product Care

To keep your telephone working and looking good, follow these guidelines:

•

Avoid putting the phone near heating appliances and devices that generate electrical noise (for example, motors or ﬂuorescent lamps).

DO NOT expose to direct sunlight or moisture.

Avoid dropping the handset, as well as other rough treatment to the phone.

Clean the phone with a soft cloth.

Never use a strong cleaning agent or abrasive powder because this will damage the ﬁnish.

Retain the original packaging in case you need to ship the phone at a later date.

Service

If trouble is experienced with this equipment, for repair or warranty information, please contact customer service at 1-800-511-3180. If the equip-

ment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is

resolved.

This product may be serviced only by the manufacturer or its authorized service agents. Changes or modiﬁcations not expressly approved by ATLINKS

USA, Inc. could void the user’s authority to operate this product. For instructions on how to obtain service, refer to the warranty included in this

guide or call customer service at 1-800-511-3180.

Or refer inquiries to:

ATLINKS USA, Inc.

Manager, Consumer Relations

P O Box 1976

Indianapolis, IN 46206

Attach your sales receipt to the booklet for future reference or jot down the date this product was purchased or received as a gift. This information

will be valuable if service should be required during the warranty period.

Purchase date _____________________ Name of store ___________________________________________________________

Accessory Information

Headset

AC power adaptor

5-2651

5-2425

To place order, have your Visa, MasterCard, or Discover Card ready and call toll-free 1-800-338-0376.

A shipping and handling fee will be charged upon ordering.

We are required by law to collect appropriate sales tax for each individual state, country, and locality to which the merchandise is being sent.

Items are subject to availability. *Prices are subject to change without notice.

Warranty

Limited Warranty

What your warranty covers:

•

Defects in materials or workmanship.

For how long after your purchase:

•

One year, from date of purchase. (The warranty period for rental units begins with the ﬁrst rental or 45 days from date of shipment to

the rental ﬁrm, whichever comes ﬁrst.)

What we will do:

•

Provide you with a new or, at our option, a refurbished unit. The exchange unit is under warranty for the remainder of the original

product’s warranty period.

How you get service:

•

Properly pack your unit. Include any cables, etc., which were originally provided with the product. We recommend using the original

carton and packing materials.

•

”Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that the product is within the warranty period,

must be presented to obtain warranty service.” For rental ﬁrms, proof of ﬁrst rental is also required. Also print your name and address

and a description of the defect. Send via standard UPS or its equivalent to:

ATLINKS USA, Inc.

c/o Thomson

11721 B Alameda Ave.

Socorro, Texas 79927

•

Pay any charges billed to you by the Exchange Center for service not covered by the warranty.

Insure your shipment for loss or damage. ATLINKS accepts no liability in case of damage or loss.

A new or refurbished unit will be shipped to you freight prepaid.

What your warranty does not cover:

•

Customer instruction. (Your Owner’s Manual provides information regarding operating instructions and user controls. Any additional

information, should be obtained from your dealer.)

•

Installation and setup service adjustments.

Batteries.

Damage from misuse or neglect.

Products which have been modiﬁed or incorporated into other products.

Products purchased or serviced outside the USA.

Acts of nature, such as but not limited to lightning damage.

Product Registration:

•

Please complete and mail the Product Registration Card packed with your unit. It will make it easier to contact you should it ever be

necessary. The return of the card is not required for warranty coverage.

Limitation of Warranty:

•

THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED

(INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO

VERBAL OR WRITTEN INFORMATION GIVEN BY ATLINKS USA, INC., ITS AGENTS, OR EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY

WAY INCREASE THE SCOPE OF THIS WARRANTY.

•

REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER. ATLINKS USA, INC.

SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT

OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER OF WARRANTIES AND LIMITED WAR-

RANTY ARE GOVERNED BY THE LAWS OF THE STATE OF INDIANA. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED

WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED TO THE APPLICABLE WAR-

RANTY PERIOD SET FORTH ABOVE.

How state law relates to this warranty:

•

Some states do not allow the exclusion nor limitation of incidental or consequential damages, or limitations on how long an implied

warranty lasts so the above limitations or exclusions may not apply to you.

•

This warranty gives you speciﬁc legal rights, and you also may have other rights that vary from state to state.

If you purchased your product outside the USA:

This warranty does not apply. Contact your dealer for warranty information.

•

Index

Accessing the Answering System from Another Location 25

General Product Care

Accessory Information

Answering an Intercom Call

Answering Calls 16

Hearing Aid Compatibility 3

Hold 17

Hour Format

Answering Machine

Answering System

Auto Attendant 25

Auto Attendant Pickup Delay

Auto Attendant Sequence for Callers

If You Did Not Program Your Local Area Code21

If You Programmed Your Local Area Code

Important Installation Guidelines

Important Installation Information 6

Base Layout

Basic Operation 16

Installing the Phone

Intercom Auto Answer

Intercom Calls

Intercom Conference Calls 19

Intercom Hold 19

Call Alert Tone 10

Call Screening

Call Waiting Caller ID

Caller ID 20

Interference Information 2

Chain Dialing

Clear All Memories

Conference Calls 18

Connecting with the Answering System

Language

Licensing

Limited Warranty 29

Local Area Code 11

Cordless Phone Option

Mailbox 14

Data Port

Delay Ring

Deleting a CID Record

Deleting All Call Records 20

Deleting Messages 24

Dialing a Stored Number 22

Dialing Back 21

Display Contrast 11

Display Messages 27

Do Not Disturb 17

Making Calls with the Handset

Making Calls with the Optional Headset

Making Calls with the Speakerphone

Manually Setting the Time and Date11

Memo Recording 24

Memory Delete/Clear

Memory Log and Phone Book (Directory) Memory

Message Interrupt

Message Length 13

Message Playback24

Monitoring Incoming Calls 24

Mute 17

Editing Name Number Stored in Phone Book Memory 22

Editing Name Number Stored in the Intercom/Memory Log 22

Equipment Approval Information

No Unknown/Blocked

FCC RF Radiation Exposure Statement

Flash 17

Flash Time

One-Touch Intercom

Operation By Battery

Operation without Power 27

Saving CID Record to Intercom/Memory Log or

Phone Book Memory

Service 28

Other System Phones

Set Day Time for Auto Attendant 14

Set Night Time for Auto Attendant 15

Set Night Time ON / OFF 15

Set Valid ID

Set Weekend Greeting

Speakerphone, Handset, and Headset Volume18

Paging All Stations

Parts Checklist

Phone ID

Storing a Number and Name in Memory

Storing a Pause in Memory22

Phone Name

Pickup Delay

Storing the Last Number Dialed

Summary Screen 20

Placing a Call on Hold

Playback and Erasing a Greeting

Playback and Erasing Auto Attendant Greetings

Switching Between the Speakerphone, Handset, & Headset 17

System Verification

Pre-dialing

Priority Line

Privacy 18

Programming the Answering Machine

Programming the Auto Attendant 14

Telephone Jack Requirements

Toll Saver Operation 25

Transferring a Call to Another Station

Troubleshooting Guide 27

Turn Auto Attendant On/Off

Turning the Answering System On/Off

Programming the Telephone

Providing Privacy 18

Two-Way Recording

Receiving a Transferred Call from Another Station

Receiving and Storing CID Records 20

Recording a Greeting

Recording Auto Attendant Greetings

Using Multiple Auto Attendants

Recording Incoming Messages

Redial 17

Regional Area Codes

Volume 18

Releasing a Call from Hold 17

Remote Password 13

Restoring the Default Settings

Reviewing CID Records

Reviewing Phone Book (Directory) Memory 22

Reviewing the Intercom/Memory Log 22

Reviewing the Redial Numbers 17

Ringer Tone

Ringer Volume 18

Visit the RCA web site at www.rca.com

Please do not send any products to the Indianapolis address listed in this manual or on the carton. This will only add delays in service for

your product.

ATLINKS USA, Inc.

101 West 103rd Street

Indianapolis, IN 46290

Trademark(s)® Registered

Marca(s) Registrada(s)

Model 25415

00000556 (Rev. 0 E)

05-13

Printed in China

Radio Shack Handheld Game System 60 2708 User Guide
Rotel Stereo Amplifier RC 1090 User Guide
Ruby Tech Switch GS 5105M User Guide
Samsung Cell Phone 9330 User Guide
Samsung Cell Phone GH68 04434A User Guide
Samsung Home Theater System SEK 1000 User Guide
Samsung VCR VR5160 User Guide
Sanyo Freezer MDF 136 User Guide
Sceptre Technologies Flat Panel Television E195 User Guide
Sears Automobile Battery Charger 287124 User Guide