Step 3: Hanging display
Firstly lift the bracket mounted display over the wall mount. And then hook the
brackets over the top of the wall mount. Rotate the display let the bottom of the
brackets hook over the bottom of wall mount, as shown in Fig.3a. Then put safe
bolts into the bottom of the brackets and lock it, as shown in Fig.3b.
Fixed Flat Panel TV Bracket
Multifunctional double deck wall mount
INSTALLATION GUIDE
Warning: Some TV require two people to lift, as we are not responsible for any
personal injury or product damage due to mishandling.
Item No.:PSW116MF1
UP
UP
UP
UP
2
1
3
Fig 3a
Fig 3b
Thank you for choosiing our products
Easy installing: Just hang up the display
Safety: locking by spinning bolt on the bottom
Max load capacity:60kgs/132lbs
TV size range: 36"~65"
Inside has balance adjust system
Pyle Audio
1600 63rd st , Brooklyn, NY, 11204
(718)236-8000
www.pyleaudio.com
Bulit in leveler system
MADE IN CHINA
-8-
IMPORTANT: If don’t understand about right install ways, please
consult to normal installing specialist.
Step 2: Attach mount to wall
WARNING
First, determine the height of stand
The best height of stand is parallel to eyelevel of a person who sitting on a couch.
Normally, the horizontal distance of eyelevel is about 4’ from ground level.
The following two conditions are for determining the perfect height of stand:
1) the distance between wall and couch(Fig 2a).
We are not responsible for any personal injury or product damage due to mishandling,
incorrect mounting, incorrect assembly or incorrect use of this product.
Note: The supplied wall mounting hardware is not for use on steel stud walls or cold
cinder block walls. If you are uncertain about the nature of your wall, please consult a
qualified contractor. If the hardware you required is not included please contact your
local hardware store.
2) the distance of eyelevel from ground level plus the distance measured from
eyelevel of a person sitting on couch with viewing angle of 15°(Fig 2a).
For example:
Caution:
This Product LCD /Plasma Wall Mount Bracket is intended for use only
1) the distance of ‘a’ is 5’-7’, the distance of ‘b’ is about 1’
2) the distance of ‘a’ is 8’-13’, the distance of ‘b’ is about 3’
3) the distance of ‘a’ is 14’-17’, the distance of ‘b’ is about 4’
The perfect height of stand centre will be anywhere within b, where you feel
comfortable for viewing.
with the maximum weights indicated .See apparatus instructions .Use with products
heavier than the maximum weights indicated may result in instability causing possible
injury .
Step 1: Attach bracket to TV
According your display hole's distance to choose the bracket :
Short bracket -up to 400mm height of landed inserts
Long bracket -up to 600mm height of landed inserts
15 degree
viewing angle
b
Check your TV manual to confirm the diameter of bolt to be used or choose an
appropriate bolt according to size, height and position of the holes on your TV. See
pages 4-5 of these instructions for examples.
eyelevel
For correct installing, make sure that hook of every bracket must facing down. Use
selected bolts, spacers and washers for installing bracket at the back of display.
Adjust two brackets to equal heights and level. Once aligned, tightly secure the
bolts. Note: the " UP"side on the top. As shown in Fig.1.
a
IMPORTANT: Don't force the bolt into the hole, which will cause a damage of
Fig 2a
equipments and injure of person. Don't use electric drill to fasten any bolts.
Fig.1
-3-
-6-
Following examples shows how to use bolts, spacers and square washers.
2. Some displays have curved backs with
recessed mounting lands(Fig.a). It will
require the use of spacer. For this display,
install a spacer(M) between display and the
bracket. As shown in Fig 1b.
1.Some displays have vertical backs. No spacer is required. Install the bracket directly
to the back of display by using bolts and square washers provided. As shown in Fig.1a.
Fig a
M4 Fig bit
M5 Fig bit
M5 Fig bit
M6 Fig bit
M
I
M
I
I
A,B
F
2
2
2
C
G
2
I
2
2
I
E
D
I
M
2
H
I
M6 Fig bit
M8 Fig bit
M8 Fig bit
Fig 1b
Fig 1a
-5-
-4-
|