P Z R 6 X A
P Z R 1 0 X A
A m p l i f i e r
A m p l i f i e r
Limited Warranty
All PYLE PRO products are carefully constructed and tested before
shipment. Units purchased in the USA are warranted to be free of
defects in material and workmanship for two (2) years from the date
of purchase. This warranty is limited to the original retail purchaser
of the amplifier.
P Z R 3 0 X A
P Z R 5 0 X A
A m p l i f i e r
A m p l i f i e r
Should the unit fail due to factory defects in material or workmanship,
your unit will be repaired or replaced at the sole discretion of PYLE.
To obtain warranty service, you must first call our Consumer Return
Hotline at (718) 236-6948 to obtain a Return Authorization Number.
This R.A. # must appear on the outside of your package and on all
paperwork relating to your return.
When returning the unit to us for warranty service, it must be carefully
packed and shipped, prepaid, to:
R.A.#: _____________
PYLE PRO Service Center
1600 63rd Street
Brooklyn, NY 11204
You must also include the following items with your return:
• A copy of your sales receipt or other proof of purchase
• A brief letter, indicating the problem you are experiencing
with the product
• Include in your letter your return address, daytime phone
number and R.A. number
• Also include a check or money order for $15.00 for return
shipping, handling and insurance, or provide your Visa/MC
number with expiration date.
Our obligation under this warranty is limited to the repair or replacement
of the defective unit when it is returned to us prepaid. This warranty
will be considered void if the unit was tampered with, improperly
serviced or subject to misuse, neglect or accidental damage.
Owner’s Manual
INSTALLATION GUIDELINES
Connecting an equalizer or external signal processor
Connect the processor's OUT to the amplifier's IN connector.
STEREO OPERATION
Connecting the GND (GROUND) screw terminal Connecting
a mixer or preamplifier may cause excessive noise or hum
in the amplifier output. To prevent this, connect one end
of a low-capacitance shield wire to the amplifier's ground
screw (on the rear panel). Then connect the other end of
this wire to the ground terminal on the mixer or preamplifier
enclosure.
CH 2
CH 1
SWITCH IN “STEREO” POSITION
B
ALANCED
I
N
P
U
T
S
OUTPUTS
CAUTION:
CAUTION:
DISCONNECT SUPPL CORD BEFORE CHANGING FUSE.
Y
CH-2
CH-1
FOR CONTINUED PROTECTION AGAINST RISK OF FIRE
REPLACE ONLY WITH SAME TYPE FUSE.
CAUTION:
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED)
PLUG WITH AN EXTENSION CORD RECEPTACLE
2
3
1
OR OTHER OUTLET UNLESS THE BLADES CAN BE FULL
Y
INSERTED TO PREVENT BLADE EXPOSURE
INPUTS
BRIDGE
CAUTION
~
AC
1
20V 60H
Z
CH-2
CH-1
R
I
S
K
O
D
F
O
E
L
N
E
O
C
T
T
O
R
I
P
C
E
S
N
H
O
C
K
CH-2
CH-1
MONO
STEREO BRIDGE
GND
GROUND LIFT
GROUND
LIFT
CH 2
PREAMP OR MIXER
CH 1
B
ALANCE
D
I
N
P
U
T
S
MONO SIGNAL SOURCE
OUTPUTS
CAUTION:
CAUTION:
DISCONNECT SUPPL CORD BEFORE CHANGING FUSE.
Y
CH-2
CH-1
FOR CONTINUED PROTECTION AGAINST RISK OF FIRE
REPLACE ONLY WITH SAME TYPE FUSE.
EQ OR MIXER
EQ OR MIXER
CAUTION:
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED)
PLUG ITH AN EXTENSION CORD RECEPTACLE
OR OTHER OUTLET UNLESS THE BLADES CAN BE FULL
USE
2
3
1
W
Y
INSERTED TO PREVENT BLADE EXPOSURE
INPUTS
BRIDGE
CAUTION
~
AC
1
20V 60H
Z
CH-2
CH-1
R
I
S
K
O
D
F
O
E
L
N
E
O
C
T
T
O
R
I
P
C
E
S
N
H
O
C
K
CHANNEL 1
INPUT ONLY
CH-2
CH-1
MONO
STEREO BRIDGE
GND
GROUND LIFT
GROUND
LIFT
B
ALANCED
I
N
P
U
T
S
OUTPUTS
CAUTION:
CAUTION:
DISCONNECT SUPPL CORD BEFORE CHANGING FUSE.
Y
CH-2
CH-1
FOR CONTINUED PROTECTION AGAINST RISK OF FIRE
REPLACE ONLY WITH SAME TYPE FUSE.
CAUTION! Do not use
balanced and unbalanced
inputs simultaneously!!
CAUTION:
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED)
PLUG WITH AN EXTENSION CORD RECEPTACLE
2
3
1
GROUND
SCREW
OR OTHER OUTLET UNLESS THE BLADES CAN BE FULL
Y
LOW CAPACITANCE SHIELDED WIRE
INSERTED TO PREVENT BLADE EXPOSURE
INPUTS
BRIDGE
CAUTION
~
AC
1
20V 60H
Z
CH-2
CH-1
R
I
S
K
O
D
F
O
E
L
N
E
O
C
T
T
O
R
I
P
C
E
S
N
H
O
C
K
CH-2
CH-1
MONO
STEREO BRIDGE
GND
GROUND LIFT
GROUND
LIFT
Bridged Mode Operation
This amplifier can operate in a mono bridged output mode, if
your speakers can handle the following power output levels:
STEREO SIGNAL SOURCE
As shown in the diagram below, connect the speaker's positive
(+) to the amplifier's red speakers left (1/2) terminals and
negative (-) to red speakers right (1/2) terminals.
CAUTION! Do not use
balanced and unbalanced
inputs simultaneously!!
PREAMP OR MIXER
LOW CAPACITANCE SHIELD WIRE
The speaker right (+) on the amplifier is used as a negative (-)
terminal for a bridged connection.
GROUND SCREW
NOTE: The extra amplifier output of 6.35mm phone
jacks can not be used for the bridged connection. It can only
be used in normal (non-bridged) operation as a stereo speaker
output.
EQ OR MIXER
CH 2
CH 1
Input connections
These amplifiers accept a board range of input sources,
including Compact Disc (CD,DVD) players; Cassette, Reel-
to-Reel or other tape players; Radio Tuners; Equalizers;
Signal Processors.
use XLR/6.35mm combo jacks
MONO BRIDGED OPERATION
SWITCH IN “BRIDGED” POSITION
Stereo or Mono Inputs
Your Pyle Pro amplifier can be operated in Stereo, Mono or
Bridged mode, depending on the input source. If the input
signal is mono, slide the Stereo/Mono/Bridged selector
switch to MONO and the signal will be routed through both
channels. If you wish to run the amplifier in bridged output
mode, slide the switch to Bridged.
Connecting a CD, DVD, tape player or tuner
In a normal installation, one would use the RCA JACKS for
connecting a CD player, DVD player,tape player or tuner.
DO NOT USE
BLACK TERMINALS
STEREO SIGNAL SOURCE
Speaker connections
You can connect 4 Ohm, 8 Ohm or 16 Ohm speakers to
Channel 1 and/or Channel 2 of the amplifier. If you connect
two pairs of speakers, be sure to follow these guidelines:
B
ALANCED
I
N
P
U
T
S
OUTPUTS
CAUTION:
CAUTION:
DISCONNECT SUPPL CORD BEFORE CHANGING FUSE.
Y
CAUTION! Do not use
balanced and unbalanced
inputs simultaneously!!
CH-2
CH-1
FOR CONTINUED PROTECTION AGAINST RISK OF FIRE
REPLACE ONLY WITH SAME TYPE FUSE.
CAUTION:
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED)
PLUG WITH AN EXTENSION CORD RECEPTACLE
2
3
1
B
ALANCED
I
N
P
U
T
S
OR OTHER OUTLET UNLESS THE BLADES CAN BE FULL
Y
OUTPUTS
CAUTION:
CAUTION:
DISCONNECT SUPPL CORD BEFORE CHANGING FUSE.
Y
INSERTED TO PREVENT BLADE EXPOSURE
CH-2
CH-1
FOR CONTINUED PROTECTION AGAINST RISK OF FIRE
REPLACE ONLY WITH SAME TYPE FUSE.
INPUTS
BRIDGE
CAUTION
~
AC
1
20V 60H
Z
CH-2
CH-1
R
I
S
K
O
D
F
O
E
L
N
E
O
C
T
T
O
R
I
P
C
E
S
N
H
O
C
K
2
3
1
CAUTION:
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED)
PLUG WITH AN EXTENSION CORD RECEPTACLE
OR OTHER OUTLET UNLESS THE BLADES CAN BE FULL
Y
INSERTED TO PREVENT BLADE EXPOSURE
INPUTS
CH-2
CH-1
MONO
STEREO BRIDGE
BRIDGE
CAUTION
GND
GROUND LIFT
~
AC
1
20V 60H
Z
CH-2
CH-1
R
I
S
K
O
D
F
O
E
L
N
E
O
C
T
T
O
R
I
P
C
E
S
N
H
O
C
K
GROUND
LIFT
• Speakers which are connected to the same channel are
part of a pair, and must be of the same impedance.
CH-2
CH-1
MONO
STEREO BRIDGE
GND
GROUND LIFT
GROUND
LIFT
MONO OPERATION
EQ OR MIXER
SWITCH IN “MONO” POSITION
• Speakers connected to different channels are NOT part
of a pair, and can be of different impedances.
USE
CHANNEL 1
INPUT ONLY
MONO SIGNAL SOURCE
use XLR/6.35 mm
combo jacks
1. Prepare the speaker wire by removing about 1 inch of
insulation from the end of the speaker wire you intend to
connect to the amplifier. Then twist the exposed wire to
secure all the wire strands.
use RCA jacks
DO NOT USE
BLACK TERMINALS
CD PLAYER, DVD , TAPE PLAYER
OR TUNER
CH 2
CH 1
NOTE: Use 16-gauge speaker wire for lengths up to25
feet; 14-gauge wire for lengths over 25 feet. It is
recommended that you use the shortest length of wire
possible.
B
ALANCED
I
N
P
U
T
S
OUTPUTS
CAUTION:
CAUTION:
DISCONNECT SUPPL CORD BEFORE CHANGING FUSE.
Y
CH-2
CH-1
FOR CONTINUED PROTECTION AGAINST RISK OF FIRE
REPLACE ONL WITH SAME TYPE FUSE.
Y
CAUTION:
TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED)
PLUG WITH AN EXTENSION CORD RECEPTACLE
2
3
1
OR OTHER OUTLET UNLESS THE BLADES CAN BE FULL
Y
INSERTED TO PREVENT BLADE EXPOSURE
INPUTS
BRIDGE
CAUTION
2. Connect the speaker wires to the speaker's positive and
negative terminals.
~
AC
1
20V 60H
Z
CH-2
CH-1
R
I
S
K
O
D
F
O
E
L
N
E
O
C
T
T
O
R
I
P
C
E
S
N
H
O
C
K
CH-2
CH-1
MONO
GND
STEREO
BRIDGE
GROUND LIFT
GROUND
LIFT
NOTE: Most speaker terminals are either color-coded
or have a mark that indicates the terminal's polarity.
Usually positive terminals are red or have a plus symbol
(+), and negative terminals are black or have a minus
symbol (-).
MONO SIGNAL SOURCE
USE
CHANNEL 1
INPUT ONLY
MONO SIGNAL SOURCE
use RCA jacks
CD PLAYER, TAPE PLAYER
USE
CHANNEL 1
INPUT ONLY
OR TUNER
CAUTION! Do not use
balanced and unbalanced
inputs simultaneously!!
CAUTION! Do not use
balanced and unbalanced
inputs simultaneously!!
3. Connect the speaker wires to the amplifier's left and
right speaker terminals according to the terminal color
polarity.
PYLE PRO PZR6XA/10XA/30XA/50XA Amplifier Owner’s Manual – 3
2 – PYLE PRO PZR6XA/10XA/30XA/50XA Amplifier Owner’s Manual
Connecting to standard AC power
Using the Channel 1 and Channel 2 Output Level controls
Rotate output level gain clockwise to increase, or counter-
clockwise to decrease the output power. To get the best
performance with the least sound distortion, always adjust
the output level gain so the meter's pointer does not
continuously exceed the extreme right of the meter's scale.
Amplifier Specifications
PZR6XA
PZR10XA
PZR30XA
PZR50XA
After making all other connections, set the POWER switch
to OFF position. Then connect the power cord to a standard
AC outlet.
Input Impedance, balanced (unbalanced)
20 k-Ohms (10 k-Ohms)
20 k-Ohms (10 k-Ohms)
20 k-Ohms (10 k-Ohms)
20 k-Ohms (10 k-Ohms)
Continuous Output Power
Mounting the amplifier
Stereo Mode
20 Hz to 20 kHz, 8 Ohms
1 kHz, 4 Ohms
Maximum Power, 8 Ohms
Maximum Power, 4 Ohms
Peak Power, 8 Ohms
This amplifier is designed to accept standard rack mounting
installations. Two slots on each end of the front panel make
it suitable for such an installation.
70W x 2
100W x 2
110W x 2
130W x 2
1100W x 2
170W x 2
220W x 2
230W x 2
260W x 2
1650W x 2
200W x 2
300W x 2
230W x 2
350W x 2
2200W x 2
260W x 2
400W x 2
300W x 2
450W x 2
2750W x 2
CAUTION: It is possible to overdrive the amplifier by
setting output level gain too high, which may cause
damage or failure.
Tightly secure four mounting screws (not supplied) through
these fours slots and into your standard electronics equipment
rack.
About the internal clip circuitry
Special clip circuitry incorporated into your Pyle Pro
amplifier’s design protects the amplifier and speaker system
from being damaged from overdriving power.
Bridged Mode
20 Hz to 20 kHz, 8 Ohms
1 kHz, 8 Ohms
175W x 1
200W x 1
2200W x 1
380W x 1
440W x 1
3300W x 1
500W x 1
600W x 1
4400W x 1
700W x 1
800W x 1
5500W x 1
Turning the amplifier on
1. Turn on the audio input source equipment which is
connected to the amplifier INPUT jacks.
Peak Power
Under normal conditions, the amplifier’s clip indicator will
flicker as the output power momentarily exceeds the level
as set by the output level gain selector.
THD at rated output power
0.1%
10 Hz to 50 kHz
1.0V
0.1%
10 Hz to 50 kHz
1.0V
0.1%
10 Hz to 50 kHz
1.0V
0.1%
10 Hz to 50 kHz
1.0V
2. Set the amplifier’s Channel 1 and Channel 2 output level
gain controls to the minimum level settings.
Frequency Response +/– 3 dB
Input Sensitivity for rated output power
Signal-to-Noise Ratio A-Weighted
However, under excessive output conditions, the clip
indicator lights remain on continuously, alerting you that
the special clip circuitry has become active. When this
occurs, you should simply reduce the output power level
by rotating the Master Volume control counterclockwise.
3. Push in the power switch to turn the amplifier on.
Using the power blue LED meters
100 dB
100 dB
100 dB
100 dB
The meter pointer position indicates the amplifier output
power. For ease of reading in dark environments, the meter
is illuminated.
Speaker Impedance
Stereo
Bridged
4-16 Ohms
8-16 Ohms
4-16 Ohms
8-16 Ohms
4-16 Ohms
8-16 Ohms
4-16 Ohms
8-16 Ohms
120 VAC, 60 Hz / 230 VAC, 50 Hz
120 VAC, 60 Hz
120 VAC, 60 Hz
Power Requirement
Caring for your Pyle Pro Amplifier
Limited Warranty
Dimensions H x W x D, inches
(mm)
3 15/32 x 19 x 10 11/16
3 15/32 x 19 x 10 11/16
(88 x 482 x 271)
5 3/16 x 19 x 15 3/8
(132 x 482 x 390)
5 3/16 x 19 x 15 3/8
(132 x 482 x 390)
Your Pyle Pro Amplifier is an example of superior design
and craftsmanship. The following suggestions will help you
care for your amplifier so you can enjoy years of use:
(88 x 482 x 271)
All PYLE PRO products are carefully constructed and tested before shipment.
Units purchased in the USA are warranted to be free of defects in material
and workmanship for two (2) years from the date of purchase. This warranty
is limited to the original retail purchaser of the amplifier.
Weight, lbs (kg)
16.5 (7.5)
20.02 (9.1)
28.16 (12.8)
29.7 (13.5)
• Keep the amplifier dry. If it gets wet, wipe immediately.
• Use the amplifier only in well-ventilated installations.
• Handle the amplifier gently and carefully - do not drop!
• Keep the amplifier away from dust and dirt.
• Wipe occasionally with a damp cloth to keep it looking
new. Do not use harsh chemicals, solvents or
detergents!
Should the unit fail due to factory defects in material or workmanship, your
unit will be repaired or replaced at the sole discretion of PYLE.
To obtain warranty service, you must first call our Consumer Return Hotline
at (718) 236-6948 to obtain a Return Authorization Number. This R.A. # must
appear on the outside of your package and on all paperwork relating to your
return.
When returning the unit to us for warranty service, it must be carefully packed
and shipped, prepaid, to:
R.A.#: _____________
PYLE PRO Service Center
1600 63rd Street
Brooklyn, NY 11204
You must also include the following items with your return:
• A copy of your sales receipt or other proof of purchase
• A brief letter, indicating the problem you are experiencing with the
product
• Include in your letter your return address, daytime phone number and
R.A. number
• Also include a check or money order for $15.00 for return shipping,
handling and insurance, or provide your Visa/MC number with
expiration date.
Our obligation under this warranty is limited to the repair or replacement of
the defective unit when it is returned to us prepaid. This warranty will be
considered void if the unit was tampered with, improperly serviced or subject
to misuse, neglect or accidental damage.
4 – PYLE PRO PZR6XA/10XA/30XA/50XA Amplifier Owner’s Manual
PYLE PRO PZR6XA/10XA/30XA/50XA Amplifier Owner’s Manual - 5
|